Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Olympia mounting plate from Sugatsune America is a hinge mounting plate designed to be used with Olympia hinges, giving you a matched hinge and base plate setup for cabinet doors that need consistent alignment. The steel construction forms a solid base under the hinge arm, which supports stable door movement over time in typical woodworking environments. The plate provides a +7.5 mm mounting height, so it positions the hinge arm higher on the cabinet side to match hinge geometry in the Olympia system. This screw-on mounting plate uses screws as the fastening method, which gives a familiar, straightforward workflow during hinge installation or replacement on cabinets. A height adjustment of plus or minus 2.5 mm is built into the plate, letting you fine-tune the door position vertically after the hinge is mounted so you can dial in even reveals during final fit-up.
This Sugatsune Olympia mounting plate is a screw-on style plate, so installation uses screws through the four mounting holes into the cabinet side, giving you a direct, mechanical connection under the hinge. The 32 mm boring pattern aligns the plate with system holes in 32 mm case construction, which simplifies layout on cabinet sides already drilled on that spacing. With a fixed +7.5 mm height, the plate sets the base level for the hinge arm relative to the cabinet, so your door overlay and position follow the Olympia hinge design. After mounting, the height adjustment range of plus or minus 2.5 mm on the plate lets you shift the hinge position slightly up or down, which helps clean up reveal lines and corner alignments at final assembly.
This Olympia hinge mounting plate is designed to be used with Olympia hinges, so it fits into cabinet projects that are built around the Olympia hinge family from Sugatsune America. In a 32 mm line-bored cabinet, the 32 mm boring pattern lets the plate sit directly over the standard hole grid, which is useful in both shop-built and production casework using that system layout. The +7.5 mm plate height works as part of the Olympia hinge geometry, placing the hinge arm above the cabinet surface to achieve the intended door relationship to the case. Because it is a screw-on mounting plate with four screw holes, it suits wood-based cabinet sides where screws can be driven for a solid grip, such as in typical kitchen, bath, or storage cabinetry built for residential or commercial use.
The 32 mm boring pattern on this Sugatsune hinge mounting plate ties directly into standard 32 mm cabinet construction, which reduces layout time because the plate registers off the pre-drilled system holes instead of custom measurements. This alignment supports predictable hinge placement across multiple cabinets in a run, so doors line up when hung with Olympia hinges. The height adjustment of plus or minus 2.5 mm built into the mounting plate provides a practical tuning range at the hinge base, which helps you correct small door gap differences without shifting the entire cabinet or re-drilling. When combined with the +7.5 mm plate height, the adjustment lets you bring door tops and bottoms into line while still working within the intended Olympia hinge geometry. The steel construction of the Olympia mounting plate gives a rigid base under the hinge screws, which supports repeatable adjustments and sustained door operation as cabinets see regular opening and closing in service.
The Olympia mounting plate is designed to be used with Olympia hinges, which keeps the hinge arm and base plate as a matched system for predictable cabinet door alignment.
The +7.5 mm height raises the hinge arm relative to the cabinet side, setting the basic overlay and door position according to the Olympia hinge design.
The 32 mm boring pattern matches standard 32 mm cabinet line boring, so the plate aligns with those system holes and speeds layout in case construction.
The Sugatsune Olympia mounting plate is a screw-on mounting plate, so it is fastened by driving screws through the four screw holes into the cabinet side.
The hinge mounting plate offers a height adjustment of plus or minus 2.5 mm, which lets you fine-tune the mounted door vertically for even reveals.
The Sugatsune Olympia mounting plate is made from steel, providing a solid, rigid base under the hinge for typical cabinet door use.
The Sugatsune Olympia steel +7.5 mm mounting plate with 32 mm boring pattern and four screw holes brings Olympia hinge projects into a consistent layout. With screw-on mounting and a plus or minus 2.5 mm height adjustment range, it supports practical cabinet door alignment on jobs built around Olympia hinges. Choosing this Olympia mounting plate from Wurth Baer Supply ties your hinge base to the intended Olympia geometry, helping you install or service cabinetry with predictable door fit and straightforward adjustment.