Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Sugatsune Olympia mounting plate is a steel hinge mounting plate designed to be used with Olympia hinges, so it provides the base connection that lets the hinge tie reliably into the cabinet. The type is specified as +5mm, which sets the mounting plate height and helps establish the working overlay or reveal you expect across a run of doors. Height adjustment of plus or minus 2.5mm is built into the design, giving a small but important range to fine-tune the door position after the hinges are fastened. The steel fabrication with nickel finish creates a hard mounting surface that works well for repeated hinge adjustments in normal cabinet environments. This mounting plate belongs to the hinge mounting plates class, so it is intended to be part of a multi-piece hinge system rather than a standalone hinge.
This screw-on hinge mounting plate is designed to fasten directly to the cabinet body, so the hinge base sits securely on a steel support before the door is hung. The +5mm type value defines the plate height, helping installers position drilling patterns so Olympia hinges seat correctly on the case. Once the hinge and plate are assembled, the plus or minus 2.5mm height adjustment lets the door be moved slightly up or down relative to the cabinet. That adjustment range is useful when cabinet construction introduces small variances, because fine-tuning at the plate reduces the need for patching holes. The steel fabrication with nickel finish keeps the adjustment zone at the hinge interface smooth, so hinge movement and readjustments can be done cleanly during fit-out.
This Sugatsune America hinge mounting plate sits in the hinge base plates category, so it is used wherever an Olympia hinge needs a stable interface to a cabinet. It is designed to be used with Olympia hinges, which makes it suited to cabinet and casework projects already built around that hinge family. The +5mm type value fixes the offset of the hinge from the mounting surface, so in a run of cabinets the same plate helps keep overlay behavior consistent from door to door. Because it is a screw-on design, the plate installs directly to cabinet panels, such as sides or partitions, forming the foundation for the Olympia hinge arm that then attaches to the door.
The +5mm type specification on this mounting plate gives a known starting height for Olympia hinges, which matters when you are trying to match existing door reveals or build repeatable shop standards. With height adjustment of plus or minus 2.5mm available at the plate, installers can shift the hinge position slightly without altering the cabinet, helping doors align cleanly along the top and bottom edges. The steel fabrication keeps this adjustment stable once set, so the hinge can operate repeatedly without the mounting surface deforming. The nickel finish supports smooth contact at the hinge interface, which helps when small adjustments are needed as hardware is dialed in during final installation. Using the manufacturer part number 360-P6WTPLUS5 ties the plate exactly to this Olympia configuration, simplifying reorders when future cabinets must match the same hinge geometry.
The mounting plate is designed to be used with Olympia hinges, so it serves as the base component in projects built around that specific hinge series.
The +5mm type defines the mounting plate height, helping installers establish a consistent starting offset so door overlay and reveals track evenly across cabinets.
The mounting plate has a height adjustment range of plus or minus 2.5mm, allowing small vertical changes at the hinge to refine door alignment on the cabinet.
The screw-on design means the plate fastens directly with screws to the cabinet surface, creating a firm hinge base that supports accurate positioning.
The mounting plate uses steel fabrication with a nickel finish, giving a rigid support with a clean metallic appearance suited to cabinet interiors.
Part number 360-P6WTPLUS5 identifies this specific Sugatsune Olympia mounting plate configuration, supporting consistent selection for repeat or matching installations.
The Sugatsune Olympia mounting plate gives installers a defined +5mm type height and a plus or minus 2.5mm height adjustment range, so Olympia hinges can be set and fine-tuned without revisiting cabinet construction. Its screw-on design places a steel, nickel-finished base directly on cabinet panels, creating a dependable interface for the hinge arm in everyday casework. For projects built around Olympia hinges, using manufacturer part number 360-P6WTPLUS5 keeps hinge geometry consistent from cabinet to cabinet, supporting repeatable layouts in both shop-built and onsite work.