Hettich Quadro V6 350mm Soft-Close Full Extension Undermount Drawer Slides, Ball Bearing Left hand Zinc - 9245355

Hettich Quadro V6 350mm Drawer Slide For Precise Control

Hettich Quadro V6 350mm drawer slide is a full extension undermount drawer slide that supports smooth travel for standard drawer applications. The integrated Silent System controls closing, so the drawer transitions into the cabinet quietly and consistently. As a soft-close full extension undermount slide, it brings the drawer fully forward while keeping the hardware concealed under the drawer, which helps when aligning fronts in modern installations. The ball bearing design manages the running action, which supports stable movement of the loaded drawer. A load capacity up to 30 kg for standard applications lets the slide carry typical residential or light commercial contents without overstraining the runner. A version available for particularly light drawers up to 10 kg suits smaller or reduced-load drawers where a lighter running characteristic is preferred. Galvanised steel construction resists corrosion, which supports long-term use in normal cabinet environments.

Key Quadro 4D V6 Slide Details For Installers

• The Quadro 4D V6 slide uses a convenient slide on installation with 4D catches, so the drawer engages the runners quickly, which helps streamline fitting during cabinet assembly.
• Integrated Silent System provides silent and soft closing, which reduces impact at the end of travel and supports consistent gap lines over repeated use.
• Tool-less, intuitive adjustment of the drawer front panel allows front alignment using built-in controls, which speeds up fine-tuning on the job.
• Load capacity up to 30 kg for standard applications supports many everyday storage tasks, so one runner type can serve a wide range of drawer duties.
• Load capacity to EN 15338, Level 3 indicates the slide has been tested to a defined standard, which supports predictable performance in qualifying applications.
• Galvanised steel construction provides a protective zinc finish, which supports durability in typical indoor woodworking and cabinet settings.

Undermount Slide Installation And 4D Adjustment

This soft close full extension undermount slide uses a slide on installation with 4D catches, which lets the drawer be positioned onto the runners in one movement. Tool-less, intuitive adjustment of the drawer front panel means installers use only the built-in mechanisms to set front position, which simplifies work inside fitted cabinets. Height adjustment up to plus 2 mm allows the drawer front top gap to be aligned with adjacent fronts. Side adjustment up to plus or minus 1.5 mm, with a maximum drawer side profile thickness 15 mm, gives lateral tuning within defined limits, which is important when working across a cabinet bank. Depth adjustment up to plus or minus 2 mm supports aligning the front plane with neighboring doors. Tilt adjustment lets the top and bottom of the front be set relative to the cabinet, which helps correct racking or floor variations.

Using The Quadro V6 Slide In Real Projects

Where This Undermount Drawer Slide Performs Well

This undermount drawer slide belongs to the Drawer Slides & Accessories category and the Slides, Undermount subcategory, placing it in applications where concealed runners are preferred. As an undermount drawer slide, it supports projects that call for clean side profiles and full extension access to the drawer contents. The soft-close full extension undermount slide design is suited to installations where controlled closing improves user comfort, such as kitchen, bath, or furniture drawers using similar construction methods. A load capacity up to 30 kg for standard applications allows this Hettich America Corporation slide to support general storage loads in cabinetry built for everyday use. The version available for particularly light drawers up to 10 kg supports smaller formats or low-mass drawers constructed for lighter content. Load capacity to EN 15338, Level 3 ties performance to a recognized test level, which helps match this slide to projects expecting that standard of service.

Adjustment Features That Support Repeatable Results

The 4D catches and tilt adjustment give this Quadro 4D V6 slide a defined adjustment range, which helps repeat the same front alignment across multiple cabinets. Tool-less, intuitive adjustment of the drawer front panel means height, side, depth, and tilt can be tuned without additional tools on the adjustment points, which shortens time spent at each opening. Height adjustment up to plus 2 mm lets the installer shift the front upward, which helps set a consistent reveal above drawers sharing a cabinet. Side adjustment up to plus or minus 1.5 mm, with a maximum drawer side profile thickness 15 mm, keeps sideways travel within a known window, supporting predictable spacing between fronts. Depth adjustment up to plus or minus 2 mm brings the front flush with neighboring faces, which reduces post-install rework. Tilt adjustment allows the top and bottom of the front to be balanced, which helps achieve straight visual lines in tall drawer stacks.

Common Questions About This Hettich Quadro Slide

Select This Quadro V6 Slide For Controlled Motion

The Hettich Quadro V6 350mm drawer slide combines full extension undermount running, integrated Silent System, and 4D adjustment, which supports precise drawer alignment and controlled closing in standard applications. Load capacity up to 30 kg for standard applications and a version available for particularly light drawers up to 10 kg help align this runner with a range of cabinet designs. Galvanised steel construction and load capacity to EN 15338, Level 3 support performance targets set for many woodworking projects. For projects built around 350 mm undermount runners, this soft close full extension undermount slide provides a balanced option when specifying hardware through Wurth Baer Supply.