2-3/8" Diameter x 28" High Rockwell Single Table Leg, Brushed Steel
Description
Rockwell Single Table Leg 28 Inch For Stable Support
Rockwell single table leg 28 inch defines this Peter Meier table support as a dedicated leg for work surfaces and tables, so you get a clear, repeatable solution when building or modifying a table. The 2-3/8 inch diameter steel construction concentrates support into a compact footprint, which helps keep the leg stout while staying out of the way of knees and storage. The 28 inch high dimension sets a standard work surface or table height, giving cabinetmakers and installers a consistent reference when laying out tops and frames. The brushed steel finish provides a clean, professional look that blends with many commercial and residential interiors, which helps finished projects look uniform across multiple legs and stations.
Key Rockwell Table Leg Details For Daily Work
- The 2-3/8 inch diameter profile focuses strength into a single vertical member, which helps the leg handle typical work surface loads while remaining visually slim under the top.
- The 28 inch high size matches common table and work surface heights, so fabricating new stations or aligning with existing cabinetry follows a familiar dimension.
- The brushed steel finish gives the leg a neutral, metallic appearance, allowing it to coordinate with a range of laminates and hardware without drawing attention.
- The 4 9/16 inch (116mm) square mounting plate spreads load across a wider area of the underside, which supports a secure connection to the work surface or table top.
- The design as a single leg supports layouts where only one vertical support is needed, such as open corners or peninsula work surfaces.
Mounting Plate And Adjustable Foot Setup Details
The 4 9/16 inch (116mm) square mounting plate on this Rockwell single table leg creates a generous contact area under the top, which helps distribute forces and reduce point stress on the substrate. The plate geometry provides predictable edge distances in both directions, giving fabricators a straightforward layout reference when locating the leg. The 1 1/8 inch adjustable foot at the bottom of the leg adds height flexibility within that range, which helps installers dial in final work surface level where floors are out of plane. This foot adjustment supports fine-tuning without altering the fixed 28 inch leg tube, saving time on-site when matching adjoining surfaces.
Using This Brushed Steel Table Leg In Projects
Where This 28 Inch Rockwell Table Leg Fits
This 2-3/8 inch diameter x 28 inch high Rockwell single table leg works in work surface and table applications where a single vertical support is appropriate, such as open-ended runs or support at one side of a countertop. The brushed steel finish suits situations where exposed metal is visible to users, helping the leg blend beneath desks, counters, and shop workstations. Its role as a table leg positions it for projects in woodworking shops and installation jobs that call for a defined support under a flat surface. With the square mounting plate, the leg connects to the underside of work surfaces in a stable pattern, supporting tops used in everyday tasks.
How The Mounting Plate And Foot Improve Results
The 4 9/16 inch (116mm) square mounting plate on this Peter Meier table leg gives installers a stable base pattern, which helps limit rocking under load once fastened to the underside. The square format simplifies orientation during layout, keeping the leg sides aligned with the table edges for a clean visual line. The 1 1/8 inch adjustable foot at the bottom allows small height corrections within that adjustment travel, so the 28 inch nominal height can be tuned to match nearby surfaces or compensate for floor variations. In practical use, this combination of fixed leg height and adjustable foot supports consistent work surface levels across multiple legs, helping reduce time spent reworking installations for level and alignment.
Common Questions About This Rockwell Table Leg
What is the height of this Rockwell single table leg?
The Rockwell single table leg is 28 inches high, so it aligns with common table and work surface heights used in many cabinet and shop layouts.
How wide is the Rockwell table leg mounting plate?
The mounting plate is 4 9/16 inches (116mm) square, which spreads load over a larger underside area and supports a solid connection to the work surface.
What does the 2-3/8 inch diameter do for this leg?
The 2-3/8 inch diameter provides a compact yet substantial tube size, helping balance strength and clearance under tables and work surfaces.
How much height adjustment does the foot provide?
The foot is adjustable 1 1/8 inches, allowing fine tuning of the finished work surface height when floors are uneven or when aligning multiple supports.
What is the finish on this Peter Meier table leg?
The table leg has a brushed steel finish, giving it a clean, neutral metal appearance that works in many commercial and residential environments.
What is the manufacturer part number for this Rockwell leg?
The manufacturer part number is 960-7S-ST, which identifies this specific 2-3/8 inch diameter x 28 inch high Rockwell single table leg in brushed steel.
Selecting This Rockwell Leg For Work Surfaces
This 2-3/8 inch diameter x 28 inch high Rockwell single table leg in brushed steel from Peter Meier offers a defined way to support a work surface or table at a standard height. The 4 9/16 inch (116mm) square mounting plate and 1 1/8 inch adjustable foot work together to give installers a stable connection to the underside and an on-site height adjustment range. For projects needing a single leg solution under a work surface or table, this Rockwell table leg delivers a clear combination of height, finish, and mounting detail suited to regular cabinet and woodworking environments.