Salice Soft-Close Silentia Full Overlay Face-Frame;Frameless Hinges Nickel, 94° Screw-On - CNA7AE9

Salice Silentia Full Overlay Hinge For Thick Doors

Salice Silentia full overlay hinge is a concealed cabinet hinge from Salice America designed for profile and thicker doors, so it supports projects where standard European hinges do not give enough clearance or control on heavy faces. This hinge belongs to the Salice Series N family, which is stated as being for profile and thicker doors, giving it a clear role when working with door designs that stand proud or use heavier materials. The hinge offers soft-close Silentia action, which slows the final swing of the door and helps it settle quietly against the face frame or cabinet side, helpful in busy shops, showrooms, or residential installations. As a full overlay hinge, it is suited to layouts where the cabinet door needs to cover the face frame or case side, aligning with many contemporary and retrofit cabinet plans.

Key Salice Series N Hinge Working Details

• The hinge has a 94 degree opening angle, which defines how far the door can swing and helps plan adjacent door clearances and hardware positions on cabinets and built-ins.
• A 12 mm deep cup is specified, so drilling depth in the door is controlled, which matters when working with thinner panel cores or decorative profiles near the hinge area.
• The hinge is for profile and thicker doors, which supports door builds using applied moldings or increased thickness where additional clearance and geometry are required.
• The stated maximum door thickness is 40 mm, giving a defined limit that helps design or verify door construction for this hinge without overbuilding beyond its intended range.
• The hinge uses a nickel finish, which offers a neutral, professional appearance inside cabinets and coordinates with common mounting plates and interior hardware finishes.
• The product is described as a screw-on hinge, so it fastens to the door and plate with screws, allowing mechanical fastening suited to woodworking environments using standard screw-driving tools.

Mounting And Drilling Setup For This Hinge

This Salice concealed cabinet hinge uses a 12 mm deep cup, so the door-side bore only needs to be drilled to that depth, which helps keep more material behind the cup on profile or thicker doors. The possible drilling distance on the door, expressed as K from 3 to 14 mm, defines how far the cup hole can sit from the door edge, giving flexibility to position the hinge based on overlay needs and door profile details. The hinge provides a 94 degree opening, which means hinge placement can be laid out knowing the door travel arc, useful when doors meet walls, appliances, or other cabinetry. Because this model is identified as screw-on, it is intended for installation using screws through the hinge flanges, fitting standard shop workflows with jigs or line-boring systems that support screw-fastened European hinges.

Using The Salice CNA7AE9 In Cabinet Projects

Where This Salice CNA7AE9 Hinge Is Applied

The Salice CNA7AE9 hinge is listed in the concealed cabinet hinges class, positioning it for hidden applications where the hardware should sit inside the cabinet while the exterior remains clean. It is part of the Salice Series N range, which the data states is for profile and thicker doors with a maximum thickness of 40 mm, so it addresses doors that move beyond standard 3/4 inch construction and may carry applied moldings. The hinge operates at 94 degrees of opening, which suits cabinets where controlled swing is preferred over very wide openings, for instance near internal dividers or tight corner situations. As a full overlay hinge for face-frame or frameless situations, it supports cabinet layouts where the door needs to cover the case front, so designers can achieve continuous door runs with minimal visible cabinet front. The nickel finish aligns with typical professional cabinet hardware selections, blending with other interior fittings while giving a uniform look across projects using Salice America components.

Why These Salice Series N Details Matter

The 12 mm deep cup on this hinge affects drilling operations by limiting how far into the door the bit must travel, which is helpful on thicker doors where maintaining material around the bore supports screw holding power and long-term hinge stability. The K drilling distance range from 3 to 14 mm allows the same hinge to adapt to different overlays and profiles, which reduces hinge variation across a job while still meeting the visual line-up and reveal targets of each door. The maximum door thickness of 40 mm sets a working envelope for designers and installers, so thick doors can be used confidently up to that dimension without moving outside the hinge geometry the manufacturer defines. Compatibility with all traditional Series 200 mounting plates and all Domi snap-on mounting plates gives flexibility in selecting plates that match the cabinet construction style, face-frame configuration, or height adjustment scheme, while keeping the same hinge head. Because this hinge is identified as soft-close Silentia, it manages closing speed as the door nears the cabinet, which can reduce slamming forces on the mounting plates and door material, supporting long-term performance of the hinge and surrounding joinery.

Common Questions About The Salice Silentia Hinge

Choose This Hinge For Thick Overlay Door Projects

The Salice Silentia full overlay hinge from Salice America combines soft-close action, a 94 degree opening, and a 12 mm cup with a maximum 40 mm door thickness rating, matching many profile and thicker door designs. Its compatibility with Series 200 and Domi mounting plates allows it to integrate into existing Salice layouts while supporting new cabinet runs. For projects managed through Wurth Baer Supply, this hinge offers a defined, concealed solution where door thickness, overlay, and controlled closing all matter on day-to-day cabinetry work.