Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Walnut edgebanding pre-glued uses real wood veneer to finish exposed plywood or panel edges with matching walnut, so cabinet runs, shelves, and furniture parts read as solid wood instead of showing core material. This Edgemate edge banding is 0.5mm thick, which follows panel contours well while keeping a low profile for a subtle edge line that blends into the face veneer. The 13/16 inch width gives extra coverage on common 3/4 inch panels, leaving trimming room for a flush, chip-free edge. Only A quality veneer is used, so grain and color read consistently along the run, helping doors, drawer fronts, and casework look uniform across multiple parts. The unfinished surface lets you stain or clear-finish the walnut with the rest of the project so the edge matches your chosen finish system.
This Edgemate walnut edgebanding uses hot melt adhesive on the back, so the glue layer is already in place when you position it on panel edges, which simplifies the setup before heating. The 0.5mm thickness responds well to heat and pressure, helping it conform to typical panel edge tolerances during application. Its 13/16 inch width gives working room on standard 3/4 inch material, so after bonding you can trim flush without exposing the substrate. The continuous fleece backing supports the veneer as you heat and press it, which helps keep the walnut face from cracking or stretching on long edges or slight curves. Because the veneer is pre-sanded to 180 grit and left unfinished, it meets typical shop finishing sequences once trimmed, so the edge can move directly into your normal stain or clear-coat workflow.
This walnut edgebanding is real wood pre-glued, pre-sanded, and unfinished, so it works well anywhere you want exposed panel edges to match walnut faces and then take stain or clear finish together. The A quality veneer grade supports visible locations such as cabinet sides, face edges of shelves, and furniture components where grain consistency matters. At 0.5mm thick, the material suits residential and commercial woodworking where a thin, easy-to-trim edge is preferred over a heavier band, especially on plywood or composite cores. The 13/16 inch width aligns well with 3/4 inch panel stock used in cabinets, built-ins, and casework, providing slight overhang that simplifies trimming. With 50 foot and 250 foot roll options, the same product can handle small shop projects, repairs, or long production runs that require continuous walnut appearance.
The veneer is expertly matched and sanded, and the joints are described as undetectable finger jointed, so grain and color transitions stay subtle along the length, helping multiple cabinets or panels read as one coordinated set. Lamination to a continuous fleece membrane keeps the thin 0.5mm walnut supported, which helps prevent edge damage while feeding pieces across trimming or sanding operations. The hot melt adhesive coating on the back acts as a ready-to-use glue layer, so heating and pressing can be performed in a consistent way from one piece to the next without measuring liquid adhesive. Pre-sanding to 180 grit establishes a uniform scratch pattern on the walnut surface, which supports even stain absorption or clear finish build along the edge compared to unsanded veneer. Because the wood is unfinished, it integrates into your existing finishing steps on the same schedule as the panel faces, which helps maintain consistent color and sheen from face to edge.
This Edgemate walnut edgebanding is 0.5mm thick, which makes it flexible during application and easy to trim flush without creating a heavy edge profile on 3/4 inch panels.
The edgebanding is 13/16 inch wide, providing slight overhang on standard 3/4 inch material so you can trim back to a clean, full-coverage edge.
The walnut edgebanding is coated with hot melt adhesive, so the glue is activated by heat during application, helping create a consistent bond along the edge.
The walnut veneer is pre-sanded to 180 grit and is unfinished, so it is prepared to accept stain or clear finishes as part of your normal finishing sequence.
This product uses only A quality veneer, providing consistent walnut appearance along cabinet edges, shelves, and furniture components.
This walnut edgebanding is sold in full rolls of 50 feet and 250 feet, giving options suited to small projects or extended production runs.
The Edgemate walnut edgebanding real wood pre-glued, pre-sanded, and unfinished design brings panel edges in line with walnut-faced work, which supports clean, unified cabinet and furniture builds. The 0.5mm thickness and 13/16 inch width match common shop dimensions, simplifying trimming and finishing steps on 3/4 inch material. With hot melt adhesive already applied and veneer laminated to a continuous fleece membrane, this roll format is set up for efficient edge runs on both short custom jobs and longer production batches.
Sold In: 250 Lineal Ft
