Spoon Shaped Shelf Supports 5 Mm Bore Use
Spoon Shaped Shelf Supports 5 mm Bore give cabinets, closets, and garage shelves a defined bearing point that matches a 5 mm bore, so shelves sit where the layout demands. The spoon shaped design creates a distinct rest area that carries the shelf edge in a small, controlled footprint, which matters when working in tight cabinet interiors. The product sits in the Shelf, Closet & Garage Organization category as a Shelf Support, so it suits typical storage layouts where adjustable or fixed shelves rely on pin-style supports. Brand designation as Pro Value Series identifies this as part of a professional-focused line, which fits shops that repeat the same hardware across multiple jobs. The SAP description identifying SHELFREST, BRASS 5MM signals that this variant uses a brass finish in a 5 mm format, pairing visual consistency with a widely used bore size across many cabinet systems.
Key Shelf Support Details That Help On Site
- The spoon shaped support design focuses load onto a defined 3/8 long and 5/16 wide rest area, so shelf edges register predictably along the cabinet side and reduce shifting during normal use.
- The 5 mm bore requirement locks this support to 5 mm drilling patterns, which simplifies layout when line-boring cabinet sides or matching existing 5 mm systems in closets and garages.
- The 5 mm bore pin length of 3/8 provides a short engagement into the panel, which helps when panels are thinner and there is limited depth behind the bore for the support pin.
- The brass finish option called out in the description gives a warm metallic look at each support point, which matters when open shelving or glass doors leave hardware visible along the cabinet sides.
- Placement in the Shelf, Closet & Garage Organization category confirms the support is intended for storage assemblies, so installers can match it to shelving projects in those spaces with confidence.
Installation Fit And Bore Layout For IF515BP
The 5 mm bore specification defines the drill size required for the IF515BP supports, so a standard 5 mm bit or line-boring pattern sets the hole size and alignment. A 5 mm bore pin length of 3/8 controls how far the pin seats into the panel, which matters when working near cabinet backs or in narrow gables. The 3/8 long and 5/16 wide shelf rest area describes the footprint that the shelf edge actually contacts, so installers can relate that dimension to shelf thickness and overhang. Because these are Shelf Supports under the Pro Value Series brand, they match common cabinet and closet drilling programs where repeatable bore spacing is critical. The brass 5 mm identification in the SAP description ties finish and bore size together, helping maintain the same look and interface across all supports on a run of cabinets.
Using Brass 5 Mm Shelf Supports In Projects
Where Spoon Shaped Shelf Supports 5 Mm Bore Work
The product sits in the Shelf, Closet & Garage Organization category, so it fits work where adjustable or fixed shelving must sit off cabinet sides in storage applications. As a Shelf Support, the spoon shaped design offers a defined landing point for the shelf edge in cabinets, wardrobes, or garage storage units that rely on 5 mm bores. The 3/8 long by 5/16 wide rest area suits shelf edges that need a compact bearing surface rather than a long bracket-style arm, which is useful in narrower boxes. Because the pin is specified for a 5 mm bore with 3/8 length, these supports integrate into cabinet sides drilled on 5 mm systems, allowing rows of holes that accept supports at various heights without layout changes.
How IF515BP Details Support Consistent Results
The SAP description SHELFREST, BRASS 5MM ties the shelf rest function, brass finish, and 5 mm sizing into one part, which simplifies reordering when projects repeat the same hardware set. The 5 mm bore pin length of 3/8 sets a fixed embed depth, so once the drilling depth is matched to that number, each support seats consistently and holds shelves at the same elevation. The 3/8 long and 5/16 wide shelf rest area gives installers a known contact patch, so they can predict how close to the cabinet side a shelf sits and how the edge lines up with doors or face frames. With Pro Value Series branding and the Shelf Supports product class, these details position the IF515BP as a standardized component in cabinet shops, making shelf layouts repeatable across multiple units and reducing variation from one cabinet run to another.
Common Questions About Pro Value Series Shelf Supports
What bore size do these Spoon Shaped Shelf Supports 5 mm Bore require?
Spoon Shaped Shelf Supports 5 mm Bore require a 5 mm bore, so cabinet sides must be drilled with 5 mm holes to accept the pin and hold the supports securely in place.
How large is the shelf rest area on the IF515BP support?
The IF515BP shelf support has a 3/8 long and 5/16 wide rest area, so the shelf edge contacts a compact, well-defined surface along the cabinet side.
What is the pin length on this brass 5 mm shelf support?
The brass 5 mm shelf support uses a 5 mm bore pin length of 3/8, which sets how deep the pin seats into the cabinet panel during installation.
Where are these Pro Value Series shelf supports typically used?
These Pro Value Series shelf supports fall under Shelf, Closet & Garage Organization, so they are suited to storage cabinets, closets, and garage shelving projects.
What does the SAP description SHELFREST, BRASS 5MM indicate?
The SAP description SHELFREST, BRASS 5MM indicates a spoon shaped shelf rest in a brass finish sized for 5 mm bores, linking finish and bore standard in one part.
How does the 5 mm bore system help cabinet layouts?
The 5 mm bore system lets these supports fit into standard 5 mm drilling patterns, so cabinet sides can use repeated rows of holes to set shelf heights consistently.
Selecting This Brass 5 Mm Shelf Support For Work
The SAP description and Web Description together define the IF515BP as a brass, spoon shaped Shelf Support with a 5 mm bore, a 5 mm bore pin length of 3/8, and a 3/8 long by 5/16 wide shelf rest area. Those fixed dimensions and the Shelf, Closet & Garage Organization classification help align this support with cabinet, closet, and garage storage projects that follow a 5 mm drilling system. For runs where a Pro Value Series component is preferred, this part number provides a consistent, repeatable option that keeps shelf heights, bore sizing, and visible brass finish aligned from one cabinet to the next.
