Spoon Shaped Shelf Supports For 5 mm Bores
Spoon Shaped Shelf Supports 5 mm Bore give cabinetmakers and installers a pin-style support designed to fit a 5 mm bore, so shelves sit on a known interface that matches common line-boring and drilling patterns. These 5 mm bore spoon shaped supports have a 3/8 inch long shelf rest area, giving the shelf edge a defined landing so loads bear on metal rather than on cabinet material alone. The 5/16 inch wide shelf rest area spreads that load over more surface, which helps the shelf sit steady in normal cabinet use. Each support has a 5 mm bore pin length of 3/8 inch, so the pin engages the sidewall over a predictable depth for consistent seating in the hole. The Pro Value Series branding identifies these as part of a professional-grade shelf support line aimed at repeatable cabinet and closet work.
Key Shelf Support Details That Help On Site
- These 5 mm bore spoon shaped supports are built for a 5 mm bore, so they work with cabinets drilled for that common pin diameter and keep layout consistent across a run of shelving.
- The 3/8 inch long shelf rest area gives each shelf a measurable bearing length, which helps when locating shelf holes so the front edge alignment stays uniform from cabinet to cabinet.
- A 5/16 inch wide shelf rest area provides a defined contact patch under the shelf, supporting the panel over more width so point pressure at the bore edge is reduced in everyday loading.
- The 5 mm bore pin length is 3/8 inch, so the pin seats to a known depth inside the side panel and helps the support register square in the hole during installation.
- These spoon shaped supports are sold in full box quantities only, which suits production and shop environments where multiple cabinets or shelving bays use the same support style.
Mounting Fit And Bore Dimensions For Shelving
These 5 mm bore spoon shaped supports are sized around a 5 mm bore, giving installers a clear match when they drill or work with pre-bored cabinet sides. The 5 mm bore pin length of 3/8 inch defines how deep the pin reaches into the panel, which matters when working with standard cabinet side thicknesses and shelf pin rows. Because the shelf rest area is 3/8 inch long and 5/16 inch wide, the bearing surface is predictable, so hole locations can be planned to keep shelf edges aligned while still keeping adequate material under the pin. Sold in full box quantities only, this configuration supports shop workflows where a single pin style is used across multiple projects.
Using Spoon Shaped Supports In Cabinet Runs
Where Spoon Shaped Shelf Supports 5 mm Bore Fit
These 5 mm bore spoon shaped supports are designed around a 5 mm bore, so they fit cabinet and closet panels that are drilled with 5 mm shelf pin holes. In line-bored systems using that bore size, the 5 mm pin diameter serves as the locating feature that ties the support to the panel geometry. With a 5 mm bore pin length of 3/8 inch, the support engages the hole over a set depth, which keeps the pin embedded inside the sidewall rather than riding shallow at the surface. The 3/8 inch long and 5/16 inch wide shelf rest area then projects from the panel face to carry the shelf, tying the shelf position directly to the drilled pattern. Because the Pro Value Series BA1306BN part is part of a shelf support product class, it fits general cabinet, closet, and shelving projects that use pin-style rests.
Details That Support Consistent Shelf Alignment
With 5 mm bore spoon shaped supports, the consistent 5 mm bore pin length of 3/8 inch helps each support seat to the same depth, which supports level shelf alignment across an entire cabinet run. The 3/8 inch long and 5/16 inch wide shelf rest area creates a repeatable step for the shelf underside, so when bores are set to the same height, shelf edges share a common plane. Being part of the Pro Value Series line, the BA1306BN spoon shelf rest stays within a standardized geometry, which matters when multiples are used across banks of cabinets or closets. Available in a nickel finish, these supports present a neutral, metallic look where the spoon-shaped rest is visible under glass, open, or lighter-colored shelves. Sold in full box quantities only, they match shop needs when stocking a single style for many installations.
Common Questions About BA1306BN Shelf Supports
What bore size do these BA1306BN spoon shelf rests use?
The Spoon Shaped Shelf Supports 5 mm Bore use a 5 mm bore, so they fit panels drilled with 5 mm shelf pin holes in cabinet or closet projects.
How large is the shelf bearing area on each support?
Each support has a 3/8 inch long and 5/16 inch wide shelf rest area, giving the shelf a defined metal landing for better support at the panel edge.
What is the pin length for these 5 mm bore supports?
The BA1306BN spoon shelf rest has a 5 mm bore pin length of 3/8 inch, so the pin engages the side panel to a consistent depth for stable seating.
Which finish is available for this BA1306BN model?
This BA1306BN Spoon Shaped Shelf Supports 5 mm Bore model is available in a nickel finish, giving a neutral metallic appearance at the shelf support points.
What product family do these spoon shaped supports belong to?
These spoon shaped shelf supports are part of the Pro Value Series, placing them in a dedicated shelf support class for cabinet and shelving work.
In what quantity are these spoon shaped supports sold?
The BA1306BN spoon shelf rest is sold in full box quantities only, which suits shops and installers handling multiple cabinets or shelving runs.
Select BA1306BN Supports For 5 mm Bore Projects
The Spoon Shaped Shelf Supports 5 mm Bore BA1306BN give you a 5 mm pin, a 3/8 inch long by 5/16 inch wide shelf rest area, and a 3/8 inch pin length in a nickel finish. Those dimensions define how the support sits in the bore and how the shelf lands on the spoon-shaped rest, which matters when laying out cabinet or closet projects. For jobs built around 5 mm bores and metal shelf rests from the Pro Value Series line, BA1306BN provides a consistent geometry that can be repeated across cabinets and shelving runs.
