HandiSOLUTIONS inside outside corner molding is designed to hide the seam in a 90 degree corner for HandiWALL slatwall panels, so the finished corner looks continuous instead of showing raw panel edges. The molding is made of extruded PVC, which creates a consistent profile along its full length for a uniform fit at the corner. The gray color matches gray HandiWALL installations, so the transition at the inside or outside corner reads as part of the wall system rather than a separate piece. The SAP description identifies this as HANDITRIM I/O CORNER MOLDING, 80'L, GRAY, so you are working with a dedicated trim piece built for these corners. The product is made in the USA, which supports dependable manufacturing control for repeatable dimensions from job to job.
This HST3080M corner molding is specifically described as inside outside corner molding, which means a single profile handles both interior and exterior 90 degree corners, simplifying layout in garages, closets, or shops laid out with HandiWALL slatwall panels. Because it is designed to hide the seam in a 90 degree corner for HandiWALL slatwall panels, the molding nests over the panel edges at the corner rather than requiring field-built trim, reducing layout time when transitioning around a corner. The extruded PVC construction maintains a uniform shape, so when installers cut the molding to height or into shorter segments, each piece keeps the same engagement with the panel edges for a consistent fit from floor to ceiling.
The HandiSOLUTIONS HandiTRIM corner molding is designed to hide the seam in a 90 degree corner for HandiWALL slatwall panels, so its primary application is at room corners or any 90 degree turn in a HandiWALL run. Because it is identified as inside outside corner molding, the same part handles both an inward and outward 90 degree corner on a slatwall layout, which helps maintain a single look at every vertical corner on the project. In use, the molding covers the joint where two HandiWALL slatwall panels meet at the corner, so you do not see the edge of the panel or the gap where the walls intersect. The gray color aligns with gray HandiWALL systems, which supports a unified appearance around the full perimeter of a garage or storage wall system. The 80 foot length description gives extended total footage available from the supplied material, allowing installers to map out multiple vertical runs from a single part number while keeping the corner detail visually consistent.
The HST3080M part number is called out as HANDITRIM I/O CORNER MOLDING, 80'L, GRAY, which clearly identifies it as the inside outside corner solution within the HandiSOLUTIONS trim family, helping installers match it correctly to HandiWALL slatwall panels on drawings or takeoffs. Because the molding is made of extruded PVC, each length holds a stable profile, so saw cuts at various heights will still sit properly over the HandiWALL panel edge and keep the joint tight from top to bottom. The design focus on hiding the seam in a 90 degree corner means the molding is dimensioned for that interface, so the corner transition appears as a neat vertical strip instead of a stepped edge where panels meet. Being made in the USA supports stable production standards, which in practical terms helps keep dimensions and color consistent when projects are phased or when service work adds new HandiWALL sections years later alongside existing gray slatwall installations.
The HST3080M HandiSOLUTIONS corner molding is designed to hide the seam in a 90 degree corner for HandiWALL slatwall panels, so it is matched to that slatwall system.
This HandiWALL corner molding is designed to hide the seam in a 90 degree corner for HandiWALL slatwall panels, covering the panel edges where two walls meet for a cleaner finished joint.
The SAP description calls it HANDITRIM I/O CORNER MOLDING, identifying it as inside outside corner molding, so the same profile is intended for both interior and exterior 90 degree HandiWALL corners.
The HandiSOLUTIONS HandiTRIM corner molding is made of extruded PVC, providing a consistent profile that cuts cleanly and maintains its shape when fitted over HandiWALL panel edges.
This corner molding is described as gray in the HANDITRIM I/O CORNER MOLDING, 80'L, GRAY listing, so it visually pairs with gray HandiWALL slatwall panel installations.
The HandiSOLUTIONS inside outside corner molding is made in the USA, supporting consistent manufacturing for repeatable fit on HandiWALL projects.
The HandiSOLUTIONS inside outside corner molding, identified by part number HST3080M, is designed to hide the seam in a 90 degree corner for HandiWALL slatwall panels, giving gray installations a continuous, finished edge at both inside and outside corners. The extruded PVC construction and 80 foot length description support planning for multiple vertical runs while keeping a uniform profile and color across the project. For HandiWALL layouts that turn corners, this gray inside outside corner molding aligns trim choice with the specified slatwall system and finish.
Sold In: 1 Each