Sugatsune Overlay Pocket Door Kit, Min. Cab. Depth 24-1/2", Door Height 27-9/16" - 35-7/16", 2-Slides, Further Door Retraction, - ALT-ST15-D10M-24
Description
Sugatsune Overlay Pocket Door Kit For Cabinets
Sugatsune overlay pocket door kit provides an overlay pocket door system that lets a cabinet door slide back into the case instead of swinging out, which helps clear the front for equipment access or workspace. The kit is specified for a minimum cabinet depth of 24-1/2 inches, so it suits deeper cases where full retraction is needed behind face planes. Door height coverage from 27-9/16 inches to 35-7/16 inches means it fits a defined band of medium-height doors, which helps standardize layouts in a run of cabinets. The system uses two slides to support the pocket action, creating a guided path that keeps the door tracking consistently as it moves. This product is part of pocket door hardware, so it is meant to be integrated into casework where a concealed door solution is required.
Overlay Pocket Door Details That Support Layout
- The overlay pocket door system provides door alignment adjustability, which helps fine-tune gaps and reveals after installation so doors line up cleanly with adjacent fronts in a run.
- An overlay amount up to 3/8 inch, or 10 mm, sets a clear overlay band, which helps with door and face-frame sizing when laying out cabinet fronts against surrounding components.
- The overlay damper unit has an adjustment screw, allowing tuning of the damping action so the closing feel can be matched to door weight and application demands.
- Fittings are designed so the door retracts further into the cabinet than the ALTST20-D10 series, which increases clearance at the cabinet front for equipment or work surfaces.
- The kit is classified as pocket door slides, tying the motion to slide-based hardware that supports smooth door travel into the cabinet cavity.
Cabinet Depth And Door Sizing For Installation
The minimum cabinet depth of 24-1/2 inches establishes the case dimension needed so the door can retract fully, which is important when planning side clearances and interior space. The specified door height range of 27-9/16 inches to 35-7/16 inches gives a defined window for door fabrication, which helps keep hardware geometry in its intended working range. The two-slides layout sets up a predictable mounting zone along the cabinet sides, which supports consistent bracket positioning across multiple units. As a pocket door hardware solution, this system is intended to be integrated during cabinet construction so slide locations, door size, and overlay can be coordinated before drilling or machining.
Using This Pocket Door Hardware In Projects
Where This Overlay Pocket Door System Fits
This overlay pocket door system is suited to cabinets that can provide at least 24-1/2 inches of depth, because that depth allows the door to move fully into the carcass without projecting into the opening. The door height capability of 27-9/16 inches through 35-7/16 inches makes it useful for mid-size doors, such as upper multimedia or workspace cabinets, where pocketing improves access to equipment or work zones. With an overlay amount up to 3/8 inch, or 10 mm, the hardware supports overlay-style fronts rather than inset doors, which is important when coordinating with other overlay cabinet lines. The product sits in the pocket door hardware and pocket door slides class, so it is meant for casework where a clean exterior surface is preferred while still allowing front access.
How Adjustment And Retraction Improve Results
Door alignment adjustability built into the overlay pocket door system lets the installer fine-tune door position after hanging, which helps correct small case or drilling variances and results in straighter reveals. The overlay damper unit with an adjustment screw gives direct control over the damping response, which lets the closing feel be matched to the specific door size within the 27-9/16 to 35-7/16 inch range. Fittings that allow the door to retract further into the cabinet than the ALTST20-D10 series create more free space in front of the cabinet, which benefits layouts where doors must clear adjacent cabinets, equipment, or workspace edges. The use of two slides to carry the door distributes the load across both slide members, which supports consistent travel over the full retraction distance. The manufacturer part number ALT-ST15-D10M-24 identifies this specific configuration, which helps distinguish it from other Sugatsune pocket door systems when matching hardware across a project.
Key Questions About ALT-ST15-D10M-24 Use
What door heights work with this Sugatsune overlay pocket door kit?
The Sugatsune overlay pocket door kit works with doors from 27-9/16 inches to 35-7/16 inches high, which helps standardize door sizing and hardware placement within that range.
How deep does the cabinet need to be for this pocket door hardware?
This pocket door hardware is specified for a minimum cabinet depth of 24-1/2 inches, which provides the space needed for the door to retract into the cabinet.
What overlay can I design for with this overlay pocket door system?
The overlay pocket door system supports an overlay amount up to 3/8 inch, or 10 mm, which guides how far the door overlaps the cabinet front.
How does the door alignment adjustability help during installation?
Door alignment adjustability allows fine-tuning of the mounted door position, which helps achieve even gaps and smooth operation in the finished cabinet run.
What is the benefit of further door retraction compared to ALTST20-D10?
Fittings that retract the door further than the ALTST20-D10 series move the door deeper into the cabinet, which increases front clearance for access or adjacent components.
What components define the motion of this pocket door slides kit?
The pocket door slides kit uses two slides, a synchronized board, and an overlay damper unit, which work together to guide and control the door movement.
Select This Pocket Door Kit For Overlay Projects
This Sugatsune overlay pocket door kit offers a defined combination of door height range, minimum cabinet depth of 24-1/2 inches, and overlay up to 3/8 inch, which simplifies planning for overlay casework. Door alignment adjustability and the adjustable overlay damper unit support clean reveals and controlled closing, valuable on visible cabinetry. Fittings that retract the door further into the cabinet than the ALTST20-D10 series create more usable space at the front. For projects calling for pocket door hardware in this size and overlay band, this ALT-ST15-D10M-24 configuration aligns the cabinet dimensions, door travel, and motion control in one coordinated system.