Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
The Sugatsune ESR-8 is an 18-inch side-mount ball bearing drawer slide built from 304 stainless steel, rated 90 lb per pair, with 3/4 extension and a hold-in anti-rebound detent that keeps the drawer closed in demanding environments. It is the right slide when the material finish is the spec that drives selection — not just aesthetics, but genuine corrosion resistance for wet, washdown, and hygiene-critical installations.
Most drawer slide applications tolerate a zinc finish without issue. The ESR-8 in stainless steel is for the settings where that assumption breaks down: commercial kitchen equipment, marine cabinetry, food-prep and food-processing environments, laboratory casework, marine vessel storage, and any humid or washdown space where a zinc-plated slide will corrode before the cabinet wears out. The hold-in anti-rebound detent adds practical value in these same settings — on a vessel or in a commercial environment, a drawer that bounces open after closing is a hazard, not just an inconvenience. The detent holds the drawer shut without damping and without a spring; the drawer stays put until pulled.
At 3/4 extension, the rearmost portion of the drawer stays inside the cabinet at full open. Choose this slide for drawers where full rear access is not a requirement and the corrosion-resistant material grade is the primary specification.
The ESR-8-18 is built from 304 stainless steel — the standard austenitic alloy for food-service and marine hardware, offering strong resistance to oxidation and most common cleaning agents. Unlike epoxy-coated or zinc-plated steel slides, the stainless construction does not depend on a surface coating for its corrosion performance; the resistance is in the alloy itself. The Sugatsune ESR-8 series is a precision-built line; the stainless members run on ball bearings in full-length raceways for smooth, controlled travel under load. The finish is the natural brushed or satin stainless surface typical of this alloy — functional and visually clean against stainless or light-colored cabinet interiors.
Commercial kitchen fabricators, marine outfitters, laboratory furniture builders, and specialty woodworkers specifying corrosion-resistant hardware all reach for this slide. It suits any cabinet installation where the environment — not budget or style — dictates the material grade. The non-handed format keeps inventory simple: stock one SKU per drawer length and pull from the same bin for every position in the case. The 90 lb per-pair rating covers the drawer loads typical in these applications, from galley storage to lab equipment drawers. This slide is for indoor and sheltered-outdoor applications consistent with 304 stainless performance; for marine above-deck or highly aggressive chemical environments, verify the alloy grade meets the specific exposure requirement before specifying.
The drawer travels approximately three-quarters of the 18-inch slide length — roughly 13 to 14 inches. The rear portion of the drawer stays inside the cabinet at full open. If you need the entire drawer to clear the cabinet face, you need a full-extension slide.
No. The hold-in anti-rebound detent is a mechanical catch that keeps the drawer closed and prevents it from bouncing back open — there is no damper and no spring assist. The drawer does not close itself and does not slow down near shut. It simply holds position once closed until intentionally pulled open.
No. The ESR-8 is non-handed — both slides in the pair are identical and fit either side of the drawer.
Side-mount ball bearing slides in this class require nominally 1/2 inch of clearance per side. Build the drawer box 1 inch narrower than the cabinet opening. Confirm the exact clearance specification against the Sugatsune ESR-8 series documentation before cutting the box.
Yes, but face-frame installations require rear support for the back end of the slide. Check whether Sugatsune offers a compatible rear mounting bracket for the ESR-8 series; rear brackets for this type of slide are typically series-specific and sold separately.
When the material grade is part of the specification — not just a preference — the Sugatsune ESR-8 in 304 stainless delivers the hold-in reliability and smooth ball bearing travel the application needs, in a slide that won't surrender to its environment.
