Knape And Vogt 24 Inch Drawer Slides For Work Surfaces

Knape and Vogt 24 inch drawer slides give full extension travel, so a 24 inch work surface or pull-out can open completely and keep the usable depth clear. The 8414 Series uses ball bearing action, which provides a smooth, consistent motion that helps drawers and pull-out tops move without sticking under normal shop or cabinet use. These slides are unhanded side mount, so the same member installs on either side of the drawer, simplifying layout when working on multiple units. The zinc finish on the slides creates a hard, uniform surface over the steel, which supports long-term use in typical cabinet environments where drawers are opened and closed repeatedly. As 8414 hold out drawer slides, they are designed to lock and maintain work surfaces in the extended open position, so a pull-out desk or keyboard shelf stays out while in use instead of drifting or sliding back.

Key KV 8414 Hold Out Drawer Slide Details

• The 8414 Series is designed to lock and maintain work surfaces in the extended open position, which helps a pull-out top remain stable while someone writes, types, or performs assembly tasks on the extended surface.
• These slides are described as full extension, so the drawer or work surface can travel out to expose its full 24 inch nominal length, giving direct access to the entire depth instead of leaving the back portion partially inside the cabinet.
• The side clearance is 1/2 inch plus 1/32 inch minus 0 inch on each side, which sets a precise sizing target for drawer box width and cabinet opening, helping installers cut parts that fit the slide geometry on the first pass.
• The slide height is 1-13/16 inch, which lets cabinetmakers confirm that the slide will fit within the available vertical space between the drawer bottom and the cabinet opening, avoiding interference with runners or applied rails.
• The 8414 Series uses a 32mm pattern, so the slide hole layout aligns with system 32 drilling, supporting efficient boring on line-boring equipment and reducing layout work on frameless or system-based cabinet runs.
• Recommended fasteners are #7 x 5/8 inch Phillips pan head screws, which match the slide hole sizing and help achieve proper bearing between the screw head and the slide without overdriving or distorting the steel members.

Side Mount Ball Bearing Drawer Slide Fit And Setup

These side mount ball bearing drawer slides are unhanded, so the same slide type installs on either the left or right side of the drawer, simplifying ordering and jobsite organization when multiple cabinets use the same hardware. The specified side clearance of 1/2 inch plus 1/32 inch minus 0 inch on each side gives a clear tolerance window for drawer box sizing, which supports smooth movement without racking when the drawer or work surface is fully extended. With a slide height of 1-13/16 inch, fabricators can coordinate drawer-bottom positioning and rail heights to avoid rubbing or contact. The 32mm pattern on the slide matches common system 32 layouts, which fits well with line-bored cabinet sides and speeds up repeatable hole placement across production runs.

Using 8414B 24 Slides In Work Surface Projects

Where These 24 Inch Slides Perform Best

The 8414B 24 drawer slide is a 24 inch full extension member, so it suits pull-out work surfaces, keyboard shelves, or equipment trays that need near-full exposure when extended. Because Knape and Vogt states that this 8414 model has a hold out feature for work surfaces, it is designed to keep the extended surface in position during use, which is valuable when a user leans on a pull-out or works over small parts. The zinc finish and ball bearing construction combine a protected steel surface with rolling elements, which helps maintain sliding quality under typical cabinet loads rather than depending on metal-to-metal friction alone. The unhanded side mount design also means the same part number works on either side, which can reduce stock complexity in shops building multiple stations or casework runs that share the same slide length.

Why These Details Support Consistent Installations

The defined side clearance of 1/2 inch plus 1/32 inch minus 0 inch on each side turns the 8414 Series into a predictable sizing reference, so once a shop dials in its drawer width formula, the same clearance can be repeated for multiple cabinets. The slide height of 1-13/16 inch provides a firm dimension for planning vertical spacing, which helps prevent interference with face frames, stretchers, or adjacent slides when layering components in a confined opening. Because the 8414 Series uses a 32mm pattern, it lines up naturally with cabinet sides bored on 32mm centers, which lets installers rely on existing drilling patterns instead of custom marking every slide location. Using #7 x 5/8 inch Phillips pan head screws as recommended fasteners matches the hole sizing in the steel members, which promotes solid clamping without distorting the slide, supporting smoother motion and longer service life during regular drawer or work-surface operation.

Common Questions About KV 8414 Work Surface Slides

Selecting These Slides For Your Next Work Surface

Choose the KV 8414B 24 when a 24 inch full extension side mount ball bearing slide with a hold out feature for work surfaces aligns with your design. The defined 1/2 inch plus 1/32 inch minus 0 inch side clearance, 1-13/16 inch height, and 32mm pattern support predictable layout across multiple cabinets using the same hardware. At Wurth Baer Supply, this Knape and Vogt slide is presented for use where a locking extended position and smooth ball bearing travel help a pull-out surface function like a stable, accessible workstation.