Fastedge prefinished wood peel and stick edgebanding gives you real wood veneer on a roll, so you can cover exposed edges with maple that visually matches wood projects and creates a continuous finished look on site. The 0.018 inch thickness keeps the profile low, which helps the strip sit tight to the substrate and reduces edge buildup that can catch or snag in everyday cabinet use. A 15/16 inch width covers standard 3/4 inch panels with a bit of overhang, giving room for a clean trim pass while still protecting the full panel edge. The 250 foot roll length supports longer runs and repeat jobs, reducing roll changes during production work and helping maintain a steady workflow. Prefinished maple surface means the face is ready to use as supplied, which keeps the focus on cutting and applying rather than additional finishing steps after application.
This Fastedge wood edgebanding relies on a high performance pressure sensitive acrylic adhesive, so firm pressure during application activates the bond and supports strong adhesion across the full edge. Because the adhesive increases in strength as it cures, initial positioning followed by consistent contact helps the strip seat well and remain in place over time. The 15/16 inch width is sized for common panel thicknesses, which supports straightforward alignment along cabinet, shelving, or panel edges without complex layout. The 0.018 inch thickness keeps the material flexible enough to follow rated inside and outside radii, while still presenting a wood veneer surface that reads as part of the panel. A 250 foot roll format supports repeated applications across multiple cabinets or runs, helping installers handle larger projects from a single roll.
Fastedge prefinished wood peel and stick edgebanding in maple fits edge finishing tasks on cabinetry, shelving, and panels where a real wood veneer surface is required. The maple veneer matches maple-based projects, so exposed substrate edges can be covered to visually blend with doors, faces, or adjacent trim. Because it is good for field repairs, installers can carry the roll to job sites to correct damaged or unfinished edges on existing installs without returning panels to the shop. Suitability for inside and outside radii means a single product can cover straight stretches along cabinet sides and gentle curves on tops or specialty pieces, simplifying material selection across a job. When used as scribe tape, the strip can bridge small irregularities between panels and walls, allowing edges to meet surrounding surfaces with a neat wood transition.
The 15/16 inch width provides predictable coverage on standard panel edges, so installers can register the strip against the face, trim the slight overhang, and achieve a consistent reveal from cabinet to cabinet. The 0.018 inch thickness offers a slim profile that reduces the amount of trimming and flush work needed, helping edges feel closer to a factory finish after light cleanup. High performance pressure sensitive acrylic adhesive on the backing bonds as pressure is applied and increases in strength as it cures, which helps the edgebanding stay seated along the full length, even on longer runs. Real wood veneer construction means the exposed face can be worked like other thin wood surfaces, supporting careful sanding or touch-up within normal veneer expectations. The 250 foot roll length provides enough material for multiple units or full room runs, allowing repeat setups and techniques to be used across a project for consistent results.
This Fastedge edgebanding is made from high quality real wood veneers, so the finished edge presents an authentic maple wood surface that visually aligns with wood cabinet and panel projects.
The Fastedge maple strip is 0.018 inch thick, providing a low-profile veneer that conforms to rated inside and outside radii while minimizing edge buildup on cabinet and panel projects.
This Fastedge maple edgebanding is supplied as a 15/16 inch wide by 250 foot roll, supporting multiple cabinet runs and standard panel edge coverage in a single continuous length.
The peel and stick edgebanding is good for field repairs, inside and outside radii, and scribe tape applications, so it serves straight edges, gentle curves, and small transitions at adjacent surfaces.
Fastedge uses a high performance pressure sensitive acrylic adhesive on the backing, which bonds under pressure and increases in strength as it cures for a long lasting edge attachment.
The manufacturer part number is FE.PW.15/16-250.MP, providing a precise reference when specifying this Fastcap Fastedge maple edgebanding for shop stock or project requirements.
Fastedge prefinished wood peel and stick edgebanding in maple combines real wood veneer, a 0.018 inch slim profile, and 15/16 inch by 250 foot sizing to support cabinet and panel edging, repairs, and scribe work. The high performance pressure sensitive acrylic adhesive backing engages under pressure and strengthens as it cures, so edges stay bonded as projects go into regular use. For installers and shops needing consistent maple edges across straight runs, gentle radii, and on-site touchups, this Fastcap Fastedge roll provides a single material that aligns with those tasks.
Sold In: 1 Roll
