Steel table legs 7 inch adjustment 34-1/4 inch

Steel Table Legs 7 Inch Adjustment For Work Surfaces

Steel table legs 7 inch adjustment give you a straightforward way to set solid table height while handling heavy loads. This Camar Studio Series leg is a steel table leg with a 2 inch diameter, so it delivers a compact profile that still supports work surfaces. The leg height of 34-1/4 inch targets typical work surface and table applications where a consistent finished height is needed. The brushed steel finish provides a clean, neutral look that fits into a range of shop or office environments. A 660 lb per leg load bearing capacity means each leg can handle substantial weight from tops, equipment, or stacked materials. The leg uses built-in foot adjustment across 7 inches, which lets you compensate for floor variation or fine-tune working height along that range.

Key Steel Table Leg Details For Projects

• The 2 inch diameter steel construction concentrates strength into a compact footprint, which helps when laying out legs near edges or corners without sacrificing load capacity.
• The 34-1/4 inch leg height sets a baseline for table or work surface projects, giving you a predictable starting dimension before using the built-in 7 inch adjustment in the foot.
• The 7 inch adjustment in the foot lets you raise or lower the support point within that range, so you can address uneven floors or align multiple tables along the same plane.
• The 660 lb per leg load bearing capacity allows you to plan for heavy tabletops or equipment, which supports layouts using fewer legs without compromising structural performance.
• The brushed steel finish presents a neutral, finished surface that pairs with different top materials while still matching other brushed steel components in the same area.
• The Studio Series designation identifies a specific Peter Meier line, which helps when coordinating multiple legs across a room using the same style and performance characteristics.

Adjustable Foot And Bracket Mounting Function

This Camar Studio Series table leg uses built-in foot adjustment over 7 inches, so the threaded foot area provides vertical travel without separate spacers. That adjustment range works with the 34-1/4 inch leg height to cover different finished heights using the same part number. The leg interfaces with the work surface through a separate bracket, so the bracket fastens to the underside of the table and the leg connects to that bracket. This arrangement can streamline layout because the bracket position defines leg placement before the leg is attached. Screws are part of the mounting method between the bracket and the surface, so the connection relies on direct mechanical fastening into the table substrate.

Where This Studio Series Leg Fits Best

Using The Studio Series Leg In Work Areas

The Peter Meier Studio Series steel table legs with 34-1/4 inch height target work surfaces and tables that need a consistent standing or seated working level. With a 2 inch diameter, the leg suits installations where clearance around the perimeter matters, such as along walking paths or under overhangs. The 660 lb per leg load bearing capacity supports heavier tops or concentrated loads in shops, offices, or other work environments. Because the finish is brushed steel, the leg pairs with both industrial and more finished interiors while staying visually restrained. The Studio Series naming identifies it as part of a coordinated group of steel table legs, which is useful when multiple surfaces in a space should share the same appearance and performance profile.

Adjustment, Height, And Consistent Install Results

The 7 inch adjustment in the foot of this 653-9S-ST table leg means the installer can set the final table height within that span without changing the leg body. That built-in adjustability helps align adjacent tops when floors are out of level, because each leg can be tuned to carry its share of the load at the correct height. The separate bracket that attaches the leg to the table creates a defined interface between the surface and the leg, which supports repeatable positioning across multiple units. Using screws as the fastening method between bracket and table ties the leg directly into the substrate, which helps transfer the rated 660 lb per leg load into the work surface. Together, the 34-1/4 inch starting height, 7 inch foot adjustment, and bracket connection support consistent results across repeat installations.

Common Questions About Camar Steel Table Legs

Selecting This Adjustable Steel Table Leg For Work

The Camar Studio Series steel table leg with 34-1/4 inch height, 2 inch diameter, and brushed steel finish offers a defined combination of size and appearance for work surfaces. The 7 inch adjustment in the foot and 660 lb per leg capacity support demanding layouts that still need fine height control. The separate bracket connection gives a clear method for tying the leg into the underside of the table using screws. For projects that call for a steel leg with this specific height, finish, and adjustment range, this 653-9S-ST model from Wurth Baer Supply aligns directly with those requirements.