PRO Value Open Oval Flange, 3 Holes, No Pins, Dull Chrome

Screw-On Rod Support For Closet Rods

Screw-On Rod Support is a Pro Value Series zinc alloy flange designed to hold an oval closet rod, giving you a solid mounting point for hanging space in closet or storage runs. The dull chrome finish identifies the flange as a functional closet hardware component that visually matches other dull chrome pieces in the same area. The flange body is made of zinc alloy, so it provides a rigid support base wherever the rod is anchored along a wall or partition. The manufacturer describes the part as a closet rod flange with an oval layout, which helps you pair it with oval closet tubing during layout and installation. The product belongs to the closet rods and flanges class, so it is intended to serve as the stationary support piece around the rod ends or intermediate supports in a closet run.

Key Flange Details That Support Closet Work

• The flange is made of a zinc alloy, which creates a hard mounting body that resists deformation as the oval rod bears weight in everyday use.
• The dull chrome finish provides a neutral, low-sheen surface that coordinates with other dull chrome closet components for a consistent look across the installation.
• The part is identified as a closet rod flange, so it serves as the stable interface between the cabinet or wall surface and the oval closet rod during installation.
• The product is described as an oval flange, meaning its internal shape aligns with oval closet tubing and helps keep the rod from rotating at the mounting point.
• The flange has three screw holes with no pins, which spreads holding power over multiple fasteners and leaves the bore unobstructed for the oval rod.

Rod Flange Mounting And Screw Detail

The closet rod flange has three screw holes, so the installer can fasten it at three points to the cabinet side, wall, or panel to create a stable support for the oval rod. The description specifies that the flange uses #6 x 3/4" screws, which guides you to match the screw shank and length to the pre-formed holes during installation. The screw-on design means the flange is attached directly with screws through its face, so the installer positions the part on the layout line and then anchors it without extra clips or brackets. The description states that there are no pins on the flange, so the oval rod seats directly into the flange area without a pin interface, simplifying the contact point between tubing and support.

Using This Pro Value Series Rod Support

Where This Closet Rod Flange Is Applied

The manufacturer identifies the product under shelf, closet and garage organization in the closet tubing and flanges category, so it is suited for projects where hanging storage is created with closet rods. Within that category, it is defined as a closet rod flange and part of the closet rods and flanges product class, which positions it as a supporting component for rod-based hanging systems rather than a decorative trim piece. The oval reference in the description shows it is intended to work with oval closet tubing, so it fits layouts that standardize on oval rod profiles instead of round tubing. This part is branded as Pro Value Series, so it aligns with other Pro Value Series components often used together in closet and storage assemblies.

Why These Flange Details Improve Results

The zinc alloy material gives the flange a rigid structure, so when the oval rod is loaded with clothing or other hanging items, the load transfers through a solid metal body into the mounting surface. The dull chrome finish provides a subdued metal surface, which keeps light reflection down inside closet compartments while still matching other dull chrome pieces. The three screw holes allow the flange to distribute pull-out and shear forces across three #6 x 3/4" screws, so each fastener carries less load in normal service. The absence of pins means the internal flange area remains clear for the oval rod, so the installer seats the tubing without aligning it over a locating pin. The screw-on style simplifies repeat work, because the installer can replicate the same three-screw pattern wherever a support point is needed along a run. The specific manufacturer part number 54113 48 091 gives you an exact reference when aligning this flange with other matching closet tubing and flanges on a job.

Common Questions About This Rod Support Flange

Selecting This Flange For Closet Rod Runs

The Screw-On Rod Support from the Pro Value Series combines a zinc alloy body, an oval closet rod flange layout, and a dull chrome finish, so it fits well into organized closet or garage hanging systems that use oval tubing. The three-hole, screw-on mounting pattern with #6 x 3/4" screws gives you a defined fastening method that can be repeated along a wall or cabinet run. For projects calling for an oval closet rod support identified by part number 54113 48 091, this flange provides a straightforward way to connect oval closet tubing to the supporting structure.