Deltana solid brass cabinet hinges come in an array of fine finishes with ball tip finials as standard, so this CH2020U3 hinge delivers a finished look that keeps exposed hardware consistent across a run of doors. As a semi-concealed hinge in the Full Mortise Hinges category, it leaves only the key decorative elements visible while the working portions sit in the mortised edge, which helps maintain clean sightlines on face-frame cabinets. The 2 x 2 hinge sizing identified in the SAP description provides a compact footprint, which suits smaller cabinet doors where oversized hinges would crowd the stile. Being part of the Semi-Concealed Hinges product class also means the hinge supports face-frame layouts that need traditional leaf engagement without fully exposed straps, keeping the cabinet front visually balanced.
The Full Mortise mounting type listed for this Deltana CH2020U3 hinge means both leaves are designed to be set into recesses in the door edge and frame, so the metal sits flush with the wood and keeps the door margin tight. Square corners on the hinge allow mortises to be cut with straightforward square pockets, which suits jigs or templates built around sharp-corner routing rather than rounded patterns. With Holes Hinge: 6, each leaf uses multiple fasteners, so the hinge grips both the frame stile and door edge firmly and helps keep alignment stable after installation. The .093 inch hinge thickness works with mortise depths that match the leaf gauge, so the door closes without binding on the hinge side.
This product is defined in the Category as Hinges|Semi-Concealed Face-Frame Hinges|Full Mortise Hinges, so it is oriented to face-frame cabinet layouts using mortised hinge leaves. As a Semi-Concealed Hinges product class item, the design leaves part of the hinge visible while the rest is set into the frame and door, which suits cabinets where a traditional hinge line is acceptable but large decorative straps are not desired. The 2 x 2 hinge dimension in the SAP Description positions it for smaller cabinet doors where compact hardware avoids crowding narrow face frames. Mounting Type: Full Mortise allows the hinge to sit flush in the routed pockets, helping maintain uniform reveals around the door when installed with consistent mortise depth.
Deltana solid brass cabinet hinges use solid brass construction, which gives a uniform base material for the array of fine finishes mentioned in the web description, helping finishes present consistently across multiple hinges on a project. Ball tip finials as standard provide a repeatable decorative detail at each hinge end, so a bank of doors shares the same visual termination at every knuckle. The hinge thickness of .093 inch means installers can rout mortises to a single known depth, which simplifies jig setup when hanging several doors in sequence. With Holes Hinge: 6 on the hinge, screw locations are predefined and even, which supports accurate placement when transferring hole positions from door to frame. The specified wood screw size of #7 x 3/4 ties those holes to a screw that is appropriate for typical cabinet material thickness, helping maintain grip without requiring deeper drilling in standard stiles.
The Deltana CH2020U3 is a semi-concealed full mortise hinge, so its leaves are routed into the door and frame while part of the hinge remains visible for a traditional cabinet appearance.
The SAP description notes 2 x 2 hinge, polished brass, meaning each leaf is sized for a compact 2 inch by 2 inch footprint that suits smaller cabinet doors and narrow face frames.
The mounting type Full Mortise means both leaves sit in routed pockets in door and frame, helping the hinge sit flush so the door closes cleanly along the hinge side.
The web description specifies wood screw #7 x 3/4, which matches common cabinet stock depths so the hinge can be fastened securely into typical stiles and door edges.
The Holes Hinge: 6 detail means the hinge provides six screw holes, distributing load across multiple fasteners to help keep small cabinet doors aligned under regular use.
Deltana solid brass cabinet hinges in this CH2020U3 model use solid brass construction with a polished brass finish, giving a consistent bright appearance across all hinge components.
The Deltana CH2020U3 solid brass cabinet hinge pairs a 2 x 2 footprint with Full Mortise mounting, so it suits compact doors that require mortised leaves and a polished brass appearance. Square corners and a .093 inch thickness support straightforward, repeatable mortising, while Holes Hinge: 6 and the specified #7 x 3/4 wood screw detail provide a defined fastening pattern for stable door alignment. For face-frame cabinets needing a semi-concealed, polished brass hinge with ball tip finials as standard, this CH2020U3 model from Deltana Enterprises, Inc. offers a clearly specified option ready to match existing brass cabinet hardware.