Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Hickory Hardware Twist Series 3 inch pull gives cabinets a defined handhold using a 3 inch center to center hole spacing, which provides a familiar grip layout that works well when lining up multiple doors or drawers in a run. The Twist collection design evolves from organic lines found in nature and contemporary architecture, so its harmonious twist and undulating curves create contours that read as intentional design instead of a generic bar. The satin nickel finish adds a muted metallic surface, which helps the pull sit comfortably with many hinge and faucet finishes in kitchens, baths, or shop casework. A length of 3-5/8 inches sets the overall footprint on the face of the cabinet, which helps plan handle placement relative to panel edges and neighboring hardware. A 5/8 inch width defines the finger contact area, giving enough surface for a controlled pull on heavier drawers.
The 3 inch center to center specification sets the hole spacing, which lets installers drill or reuse a standard 3 inch pattern across doors and drawers for predictable alignment. The 1-1/8 inch projection value defines stand-off from the cabinet face, which keeps knuckles away from the surface during use and helps limit contact marks on finished panels. An overall length of 3-5/8 inches and a 5/8 inch width establish the rectangle of space this pull occupies on the front, which simplifies laying out hardware so it clears neighboring pulls and fits cleanly within narrow rails or stile widths.
The 3 inch center to center layout on the H076015-SN pull aligns with a common cabinet drilling standard, which suits runs of kitchen cabinets, bath vanities, and shop storage where repeating a single measurement speeds layout. The satin nickel finish lets the Twist collection design tie into other satin nickel hardware from Belwith Keeler or similar pieces, which matters when doors, drawers, and panels all share sightlines. With a 3-5/8 inch overall length, this pull fits comfortably on smaller drawer fronts or narrower door rails, which helps keep proportions balanced instead of overwhelming tight faces. The 5/8 inch width adds enough presence to show the Twist contour, which gives visual interest on flat-panel cabinetry or simple slab fronts.
The defined 3 inch center to center dimension gives a fixed mark-to-mark distance, which allows jigs or templates to be used for repeat drilling so rows of pulls line up straight along a bank of drawers. The 1-1/8 inch projection figure provides a known clearance from the cabinet face, which helps maintain consistent ergonomics on upper and lower cabinets when mixing this pull across an installation. The satin nickel finish over zinc offers a uniform surface from piece to piece, which supports consistent color and sheen when several H076015-SN pulls are installed in the same room. The Twist collection geometry with its harmonious twist and undulating curves creates a tactile ridge along the grip, which aids fingers in finding a stable hold even on taller doors that see frequent opening.
The H076015-SN pull has a 3 inch center to center spacing, an overall length of 3-5/8 inches, a projection of 1-1/8 inches, and a width of 5/8 inch, which guides drilling layout and visual placement.
The 3 inch center to center size matches a common cabinet drilling pattern, which allows straightforward hole layout or reuse of existing 3 inch spaced holes on doors and drawers.
The H076015-SN pull is made from zinc, which provides a metal structure under the satin nickel finish for a consistent feel and appearance across multiple pulls in a project.
The 1-1/8 inch projection sets how far the pull stands off the cabinet face, which helps give fingers clearance behind the handle during opening and closing.
The Twist collection pull features organic lines with a harmonious twist and undulating curves, which creates luminous contours that add visual interest to cabinet fronts.
The satin nickel finish provides a soft metallic tone, which coordinates with other satin nickel cabinet hardware and fixtures so room hardware looks consistent.
The Hickory Hardware Twist Series 3 inch pull with satin nickel finish and zinc construction combines a 3 inch center to center layout with a 3-5/8 inch length, a 1-1/8 inch projection, and a 5/8 inch width, giving installers clear measurements to plan drilling on doors and drawers. Using the defined dimensions of the H076015-SN, projects gain a consistent grip feel and an organic Twist collection look across cabinets, vanities, or storage runs. Select this satin nickel pull when a standard 3 inch center to center spacing and a shaped, twist-style profile match the visual and dimensional requirements of the job.
Sold In: 1 Each
