Hickory Hardware Twist Series satin nickel pull is a cabinet handle from the Twist collection that uses organic lines and undulating curves so doors and drawers gain a contemporary look that still ties in with natural design themes. The satin nickel finish keeps reflections soft, which helps fronts read clean in kitchen, bath, or built-in projects under varied lighting. The pull length of 9-9/16 inches gives a substantial hand grip, which helps frequent-use cabinets operate comfortably. With a center to center dimension of 8-13/16 inches (224 mm), this pull targets wider drawer fronts or tall doors that benefit from a longer handle. The 5/8 inch width keeps the profile slim, which helps layouts with tight hardware spacing stay visually light. A projection of 1-3/16 inches provides finger clearance away from the face frame.
The 224 mm (8-13/16 inch) center to center measurement on this pull fixes the hole spacing, which allows jigs or templates to be set once for a full job run. With a 9-9/16 inch overall length, the handle extends slightly beyond the screw centers, which affects where it lands relative to door edges and drawer rails. The 1-3/16 inch projection defines stand-off from the surface, which influences how fingers clear decorative edge profiles. At 5/8 inch width, the pull fits comfortably on standard stiles, which supports mounting on both framed and frameless cabinet designs where visible hardware width is a design consideration.
The Hickory Hardware Twist Series 8-13/16 inch (224 mm) center to center satin nickel pull serves cabinets and drawers that call for a longer handle, so wide drawers or tall pantry fronts gain proportional hardware. The Twist collection design evolved from organic lines found in nature and contemporary architecture, which means this pull works in spaces where designers combine modern cabinet lines with softer, curved details. The satin nickel finish presents a muted metallic surface, which helps it coordinate with satin nickel faucets, hinges, and other decorative hardware without dominating the cabinet face. Because the pull length is 9-9/16 inches with a 5/8 inch width, it occupies a balanced strip across the front, which fits banks of drawers that repeat the same handle for a unified look. The 1-3/16 inch projection keeps the grip zone separated from the door or drawer surface, which supports everyday opening even when hands are wet or gloved.
The 8-13/16 inch (224 mm) center to center layout gives installers a precise metric drilling distance, which simplifies using drilling jigs across large kitchen or commercial millwork projects. That fixed spacing helps replacements or add-ons match earlier work when the same pull is used again. The 9-9/16 inch overall length defines how close the ends of the pull approach door rails and drawer edges, which affects layout decisions when hardware must clear panel profiles or decorative trim. With a slim 5/8 inch width, the pull leaves more visible field on narrow drawer fronts, which helps retain the look of veneer or solid wood patterns. The 1-3/16 inch projection sets the handle far enough from the cabinet surface to create a clear gap, which supports a comfortable finger pull angle while keeping the handle from projecting excessively into walkways. The zinc material with a satin nickel finish controls both weight and surface appearance, which matters when specifying matching pulls across an entire Belwith Keeler decorative hardware package.
The Twist Series satin nickel pull has an 8-13/16 inch (224 mm) center to center dimension, which sets the exact drilling distance between the two mounting holes.
The Hickory Hardware Twist Series pull has a length of 9-9/16 inches, which defines the visual span of the handle across the cabinet door or drawer front.
This satin nickel cabinet pull has a 1-3/16 inch projection, which establishes the stand-off from the cabinet surface for finger clearance.
The H076020-SN satin nickel pull is 5/8 inch wide, which yields a slim front profile suitable for standard cabinet stiles.
This Twist collection pull is made from zinc with a satin nickel finish, which defines the base metal and the muted metallic appearance.
This 224 mm center to center cabinet pull is from the Hickory Hardware Twist collection and is supplied under the Belwith Keeler brand.
The Hickory Hardware Twist Series 8-13/16 inch (224 mm) center to center satin nickel pull combines a 9-9/16 inch overall length, 5/8 inch width, and 1-3/16 inch projection, so cabinet layouts gain clear drilling dimensions and a consistent visual footprint. With zinc construction and a satin nickel finish from Belwith Keeler, this handle ties into Twist collection styling while aligning with satin nickel schemes across a project. For projects sourced through Wurth Baer Supply, this specific H076020-SN pull supports repeatable cabinet hardware runs using the same established dimensions.
Sold In: 1 Each
