Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
The Salice 100 Series Logica hinge brings Silentia soft-close and toolless mounting to 1/2 inch overlay doors on face-frame and frameless cabinets, finished in nickel for a clean, hardware-coordinated look.
This is the hinge for 1/2 inch overlay doors, the partial-overlay configuration used where a door steps back from a full-cover position, and especially where two doors meet on a single center partition. The half crank arm holds the door at that overlay while the 35mm cup bores cleanly into standard doors in the 16 to 22mm range. The hinge clips to a Salice base plate mounted to the cabinet, ordered separately. Because this is a concealed Euro hinge, the plate is a required part of the installation, and Salice plates are specific to this line. For doors outside the standard thickness range, or for full overlay applications, a different hinge geometry is the right call.
The hinge body is steel with a nickel finish that holds up to the daily repetition of a working kitchen or bath. The nickel tone sits comfortably alongside brushed pulls, satin knobs, and similar hardware, so it does not compete with the visible hardware choices on the door. Silentia soft-close is built into the hinge, not bolted on after the fact, which keeps the profile clean and the damping consistent from hinge to hinge across a full cabinet run.
Cabinet shops running partial-overlay projects, contractors finishing face-frame kitchens, and designers specifying lighter-door applications will find this hinge straightforward to spec and install. The Series 100 is Salice's lighter-door line, rated for doors in the lower end of the standard weight range, so it suits upper cabinet doors and smaller case pieces rather than heavy full-height pantry doors. The toolless Logica clip speeds the install when you are hanging a room full of doors, and the adjustment gives you the control to square everything up after the boxes are set.
No. The base plate mounts to the cabinet and the hinge arm clips to it, but the plate is sold separately. Use a Salice plate matched to your cabinet construction and overlay. Plates from other brands will not connect to this hinge.
Yes, they are different. Silentia is Salice's soft-close system, which slows the door over the last few degrees of closing so it does not slam. Self-close uses a spring to pull the door shut but does not cushion it. This hinge has soft-close damping, not a self-close spring.
Yes. This hinge is rated for both cabinet types. The base plate you choose will differ depending on whether you are mounting to a face-frame stile or a frameless side panel, so select the plate that matches your box.
The right count depends on door height and weight. As general guidance, doors up to about 40 inches tall typically use two hinges, with a third added for taller or heavier doors. Check the Salice load table for the exact count on your door size and weight.
This hinge delivers soft-close performance and a coordinating nickel finish on partial-overlay doors, with toolless mounting that keeps the job moving from the first door to the last.
Sold In: 1 Each
Quantity | Unit Price | Catalog | ||||
|---|---|---|---|---|---|---|
Sold in: 3000 Each |  UBS2XX85H9 Mfr# S2XX85H9 | Flange Cover Cap, Nickel | ||||
Sold in: 1 Each |  UBS2XX86BT Mfr# S2XX86BT | Silentia Hinge Spacers 0.6mm Height For Silentia 110 Deg Hinges | ||||
Sold in: 1 Each |  UBS2XX86AT Mfr# S2XX86AT | 1.2mm Spacer for Silentia Series Hinges | ||||
Sold in: 1 Each |  UBS2XX86KT Mfr# S2XX86KT | Silentia Hinge Spacers 1.8mm Height For Silentia 110 Deg Hinges | ||||
Sold in: 1 Each |  UBD1A6ACGSN Mfr# D9A6AC3SN | Silentia Hinge Cup Depth Gauge 12 mm | ||||
Sold in: 1 Each |  UBD2ABACGSN Mfr# D2ABACGSN | Silentia Hinge Cup Depth Gauge 15.5 mm | ||||
Sold in: 1 Each |  UBS1E637XY Mfr# S1E637XY | Salice Series 100 & 700 Hinge Stop Device S1E637XY |