Nova Pro Scala H186 Drawer Member Set Purpose

Nova Pro Scala H186 drawer member set is designed as part of the Grass Nova Pro Scala drawer system, giving you a matched drawer side and slide solution for projects that need precise motion and consistent performance. This set is specified with a 154 lb dynamic load capacity, so it supports heavier drawer loads while maintaining the rated motion performance that installers expect on demanding jobs. The design provides full extension, which lets the drawer travel completely out of the cabinet opening so stored items remain visible and accessible from front to back. The integrated soft-closing function cushions the final travel, so the drawer closes in a controlled motion that protects the front and helps reduce impact on the cabinet structure over repeated use. The system is described as a slim, deep drawer side, which maintains interior storage space while still supporting higher fronts.

Key Nova Pro Scala Features For Daily Use

• The drawer member set is part of the Grass Nova Pro Scala drawer system, so it ties into a proven platform that installers can repeat across multiple cabinet runs and project types.
• A 154 lb dynamic load capacity rating means the slides are specified to handle heavier drawer contents, which supports applications that carry hardware, tools, or dense kitchen items on a regular cycle.
• Full extension travel provides access to the entire drawer depth, which simplifies placement of dividers and organizers because the rear section is just as reachable as the front when the drawer is open.
• The soft-close damping system slows the final closing movement, which reduces slamming forces on the drawer front and cabinet, helping maintain alignment of the installed fronts over time.
• Integrated height, side, and tilt adjustment lets you fine-tune the front position, which is useful when aligning multiple fronts in a bank so reveals and gaps present a clean, consistent layout.
• The drawer member set is specified as compatible with Tipmatic Soft-close, allowing it to operate with that opening and closing technology where the overall system is configured for it.

Installation-Oriented Details For Fit And Setup

The drawer member set is described as tool-free for drawer front removal and installation, which streamlines both initial mounting and later adjustments when fronts need to be repositioned or replaced. Integrated height adjustment helps you raise or lower the front in small increments, supporting tight vertical reveals between stacked drawers. Integrated side adjustment gives lateral control, allowing you to correct small offsets so the front lines up with adjacent fronts or door edges. Integrated tilt adjustment lets you set the front angle, which is particularly helpful with taller fronts so top and bottom gaps track evenly. The drawer side is specified as 7-5/16 inches high, so it supports deeper storage and taller fronts within its stated height capability. The length is specified as 24 inches, which matches cabinets designed around a 600 mm nominal drawer depth.

Nova Pro Scala Drawer Use And Alignment

Where This Nova Pro Scala Set Is Applied

This Nova Pro Scala H186 drawer member set belongs to the Grass Nova Pro Scala drawer system category, so it is intended for projects that are built around that specific platform. The drawer side is identified as slim and deep, which lets you design drawers that keep more interior volume while staying within a refined side profile suited to modern cabinetry. The set supports front heights up to 780 mm, or 30-11/16 inches, which means it can work with higher fronts such as tall pan drawers or deeper storage modules within its stated range. The 7-5/16 inch side height contributes to vertical containment of contents, which benefits situations where taller items are stored and need lateral support from the side panels.

How Design Details Support Repeatable Results

The fully-synchronized slide technology coordinates both sides of the drawer movement, helping the drawer track straight during opening and closing, which is important when tall or wide fronts are used. The soft-close damping system interacts with this synchronized motion to finish the closing cycle smoothly, which can reduce bounce-back at the face and help keep the front sitting flush against the cabinet. Integrated height, side, and tilt adjustment all reside within the system, so you can align complex front layouts using the built-in mechanisms rather than external shims. Compatibility with Tipmatic Soft-close supports applications that specify that opening and closing behavior, helping you match functional expectations across a full kitchen or commercial install. The description notes that two brackets are required per drawer, which defines the bracket usage pattern during layout. Available load capacities are stated as 88 lb and 154 lb dynamic, indicating that the system is engineered around multiple rated options.

Common Questions About This Drawer Member Set

Selecting This Nova Pro Scala Set For Projects

This Nova Pro Scala H186 drawer member set from Grass America combines a 24 inch length, 7-5/16 inch side height, and 154 lb dynamic load capacity within a single system. Full extension, soft-closing, and integrated three-way adjustment support precise, repeatable drawer alignment. Compatibility with Tipmatic Soft-close and stability up to a 780 mm front height position this set for deeper and taller drawer applications built on the Grass Nova Pro Scala platform. For projects that specify an Ice finish and require coordinated Nova Pro Scala components, this drawer member set offers a defined set of system characteristics for layout and installation planning.