Amerock Calathea Pull 128mm For Cabinet Projects

Amerock Calathea pull 128mm gives you a decorative cabinet handle built around a 5-1/16 in (128 mm) center-to-center dimension, so hole spacing lines up with common modern cabinet layouts for straightforward new installs or changeouts on doors and drawers. The pull is part of the Calathea collection, which is inspired by natural botanical patterns, so its textured surface adds visual depth when you are updating face frames, slab fronts, or furniture pieces. The polished chrome finish reflects surrounding light and colors, helping the pull read clean and bright across banks of cabinets. A projection of 1-1/16 in (27 mm) sets the gripping surface off the door or drawer front, giving fingers room to grab without contacting the wood. The zinc material supports a solid-feeling pull in hand while keeping weight reasonable on standard cabinet construction.

Key Calathea Pull Details For Daily Use

• The 5-11/16 in (144 mm) overall length spans more of the drawer or door face, so the handle visually anchors wider fronts while staying proportionate on standard cabinet sizes.
• The 1-1/16 in (27 mm) width offers a broader contact area, so fingers settle comfortably along the textured surface when you are opening and closing throughout the day.
• The center-to-center measurement of 5-1/16 in (128 mm) matches a common drilling pattern, so replacement of existing 128 mm hardware stays efficient without layout changes.
• The base length of 1/2 in (13 mm) keeps the footprint compact at each mounting point, so the pull sits neatly on narrower rails and stile sections.
• The base width of 1-1/16 in (27 mm) spreads the load where it meets the surface, which helps the pull sit stable against the face material during repeated use.
• The polished chrome finish from Amerock Corporation aligns with other bright chrome decorative hardware, which makes it easier to maintain a consistent look across a full project.

Installation Dimensions For Calathea Chrome Pull

The 5-1/16 in (128 mm) center-to-center drilling dimension defines the installation layout for this Amerock Calathea zinc pull, so installers can mark or bore holes at that fixed spacing on cabinet doors or drawers. With the 5-11/16 in (144 mm) overall length, the handle extends past the fastener points, so there is adequate clearance at each end when aligning it parallel to door edges or drawer tops. A projection of 1-1/16 in (27 mm) means the pull stands off the surface at a consistent distance, which helps doors swing and drawers slide without knuckles hitting the face. The 1-1/16 in (27 mm) width and matching base width provide a stable bearing surface, helping the pull sit flat and visually straight against painted, stained, or laminated fronts during install work.

Using The Calathea Pull In Cabinet Hardware Layouts

Where This 128mm Calathea Pull Works Best

The Calathea collection design, inspired by natural botanical patterns, delivers a textured pull that adds depth to cabinet, vanity, or furniture surfaces when a project calls for more visual interest than a flat bar. With a 5-1/16 in (128 mm) center-to-center measurement, this Amerock BP100312826 pull fits cabinet runs laid out on 128 mm drilling, so it suits many kitchen, bath, and built-in applications using that standard. The polished chrome finish pairs with other polished chrome decorative hardware and fittings, so it supports a unified look across hinges, knobs, and plumbing trim specified in the same finish family. The zinc material provides a solid construction for everyday door and drawer cycles in residential or similar environments where decorative hardware is part of the visible design.

Details That Support Consistent Handles Across Projects

The 5-11/16 in (144 mm) overall length of the Calathea pull helps installers repeat a consistent scale on wider drawers, so each front carries a handle that feels proportionate rather than undersized. The 1-1/16 in (27 mm) projection keeps the gripping area at a predictable distance from the cabinet face, which supports uniform ergonomics when the same pull is used across upper doors, base doors, and drawers. The 1-1/16 in (27 mm) width and matching base width create a balanced profile that reads the same from different viewing angles, aiding in visual alignment when hardware is laid out in rows. The 1/2 in (13 mm) base length keeps each mounting pad tight, which helps align pulls near narrow rails without overlapping into panel details. Being part of Amerock decorative hardware, this Calathea pull slots into a recognizable product class for cabinetry and moldings, which helps designers and installers coordinate it with other Amerock handles and pulls in a project schedule.

Common Questions About The Amerock Calathea Pull

Select This Calathea Pull For 128mm Layouts

This Amerock Calathea Series 5-1/16 in (128 mm) center-to-center polished chrome pull from Wurth Baer Supply ties together a known drilling standard, a textured botanical-inspired design, and a zinc construction that stands up to daily cabinet use. The 5-11/16 in (144 mm) overall length and 1-1/16 in (27 mm) projection keep sizing and clearance consistent across doors and drawers, which supports neat, repeatable hardware layouts. For projects built around polished chrome decorative hardware and 128 mm spacing, this Calathea pull offers a coordinated handle choice ready to drop into your next cabinet, vanity, or furniture run.