Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Knape and Vogt 18 inch file drawer slides provide a full extension travel, so the drawer opens its entire length and gives clear access to stored files along the slide. This model 8500-99 18 is a left hand side mount design, so it installs on the cabinet side wall rather than under the drawer. The slide uses ball bearing construction, which supports smooth motion as the bearings roll, helping the drawer move cleanly under load. A hold-in anti-rebound feature is built into the mechanism, so the drawer stays closed at the back of travel, which matters when the cabinet sees frequent opening and closing. Positive in and out stops are part of the slide design, so the drawer travel is controlled at both ends of the cycle, helping protect the drawer, face, and cabinet from over-travel impacts.
This 18 inch left hand side mount ball bearing slide is specified for a side mount installation, so it fastens directly to the cabinet side. The recommended fasteners are #7 x 1/2 inch Phillips pan head screws (BST1/2X7-2C), which match the slide hole sizing, helping the hardware seat properly along the mounting pattern. The slide delivers full extension, so when installed to the cabinet members and drawer members, the drawer box can move fully forward to its design stop, keeping files reachable without reaching past the front rail.
The Knape and Vogt model 8500-99 18 is identified as a file drawer slide, so it is intended for drawers that carry hanging or stored files. Its 18 inch length suits cabinets planned around that depth, so the drawer box can be sized to hold files front to back while staying on the slide travel. The side mount design places the cabinet members along the interior cabinet walls, so the drawer sides remain parallel to the case, which is typical for lateral or vertical file storage. With a side clearance of 1/2 inch plus 1/32 inch minus 0 inch on each side, this slide works with drawer boxes built to leave that margin, so the hardware has the space it needs to run without binding. The slide height of 3-51/64 inch, including the quick disconnect rail, defines the minimum vertical space for the hardware lane, so designers can plan drawer box heights and clearances above the slide. The 32 mm pattern support means that cabinets drilled on that system can align slide mounting holes to the boring pattern, which speeds layout in production shops using that standard. The available Anochrome finish provides a uniform appearance on the slide members, which matters when the hardware is visible on open drawers in commercial or office installations.
The 8500 series uses ball bearings with a retainer that holds three bearings per inch of race, so each inch of slide travel carries multiple bearing points, which spreads load and helps the drawer move smoothly along its path. Factory-attached drawer release clips with quick disconnect drawer members are part of the system, so once mounted, the drawer can be separated from the cabinet members at those clips, which helps during finishing, adjustment, or later service. The hold-in anti-rebound feature is designed to prevent bounce back at the closed position, so when the drawer is pushed shut, the mechanism resists the drawer rolling forward again, which matters in offices or shops where drawers are used repeatedly through the day. Positive in and out stops are integrated into the slide, so travel is controlled both at the fully closed end and at the full extension end, which helps protect fronts and hardware from overextension impacts. The recommended #7 x 1/2 inch Phillips pan head screws (BST1/2X7-2C) match the slide design, so the heads seat properly within the mounting holes and help keep the members aligned along the cabinet and drawer. This model is part of the KV 8500 line and is made in the USA, so it matches other 8500 series components in layout and function across a project.
The 8500-99 18 slide is described as a file drawer slide, so it is suited to drawers built for file storage where full extension access to the contents is important.
The slide uses a side clearance of 1/2 inch plus 1/32 inch minus 0 inch on each side, so drawer boxes can be sized to that gap for proper side mount running clearance.
The 8500-99 18 is a left hand side mount slide, so it attaches along the cabinet side wall and pairs with corresponding members on the drawer side.
This model is specified as a full extension slide, so the drawer can travel its full length out of the cabinet to reach files at the back of the box.
Factory-attached drawer release clips with quick disconnect drawer members let the drawer be released from the slide, which aids in mounting, finishing, and later adjustments.
The recommended fasteners are #7 x 1/2 inch Phillips pan head screws (BST1/2X7-2C), so the screw size and head shape match the slide holes.
The Knape and Vogt 18 inch file drawer slides in the 8500 series give a full extension, side mount solution with ball bearing action, so file drawers can open fully and operate smoothly. The hold-in anti-rebound feature, positive stops, and three bearings per inch of race help the drawer feel controlled for daily use. The specified side clearance, 32 mm pattern support, and recommended #7 x 1/2 inch Phillips pan head screws allow casework and drawer boxes to be built around known dimensions. For projects calling for an 18 inch, left hand, USA-made file drawer slide, this 8500-99 18 model aligns with that layout.
Sold In: 520 Each
