Sugatsune Overlay Pocket Door Kit, Min. Cab. Depth 16-9/16", Door Height 27-9/16" - 35-7/16", 2-Slides, Further Door Retraction, - ALT-ST15-D10M-16
Description
Overlay Pocket Door Kit For Compact Cabinets
Overlay pocket door kit ALT-ST15-D10M-16 from Sugatsune America is an overlay pocket door system designed for cabinet doors that need to slide back into the cabinet. The kit is specified for a minimum cabinet depth of 16-9/16 inches, so installers can plan carcass depth around a clear requirement. It supports door heights from 27-9/16 inches to 35-7/16 inches, which targets mid-size cabinet doors often used in multimedia, workspace, or storage applications. The system uses two slides, giving the door guided travel as it opens and retracts, which supports smoother door motion during everyday use. This product is classified as pocket door hardware, so it is intended as a structural movement system rather than decorative trim. The manufacturer part number ALT-ST15-D10M-16 links this kit directly to Sugatsune technical references and job documentation.
Key Overlay Pocket Door Details For Installers
- The overlay pocket door system offers door alignment adjustability, allowing fine tuning of the door position after installation so gaps and reveals can be dialed in for a cleaner front.
- An overlay amount of up to 3/8 inch (10 mm) lets the door overlap the cabinet opening, which supports face layouts where the door needs to cover the case edge for a finished look.
- The overlay damper unit is designed with an adjustment screw, giving installers a defined point to tweak damping performance, which helps control closing behavior without rebuilding the cabinet.
- Fittings in this system allow the door to retract further into the cabinet than the ALTST20-D10 series, which frees more front access to shelves or equipment when the door is stowed.
- The pocket door kit uses two slides as specified, so both sides of the door run on guided tracks, supporting more stable motion along the full travel path.
Installation Geometry And Overlay Adjustment Details
The minimum cabinet depth of 16-9/16 inches defines the case geometry this overlay pocket door system is designed to work within, which helps avoid conflicts between the retracted door and internal components. The supported door height range of 27-9/16 inches to 35-7/16 inches sets clear boundaries for door sizing, reducing guesswork during layout. Door alignment adjustability built into the system gives room to correct front alignment after the case is assembled, which is useful when walls or carcasses are not perfectly true. The overlay amount of up to 3/8 inch (10 mm) defines how far the door can overlap the opening, guiding hinge and front design decisions.
Using This Overlay Pocket Door System In Projects
Where This Overlay Pocket Door Kit Works Best
This overlay pocket door kit is categorized under pocket door slides within shelf, closet and garage organization as well as multimedia and workspace components, so it is oriented toward cabinets that benefit from doors clearing the front opening when stowed. The minimum cabinet depth of 16-9/16 inches points it toward cases with enough internal space for a door to fully retract, such as built-ins, media cabinets, or workspace storage. The supported door height range from 27-9/16 inches to 35-7/16 inches suits medium-height doors often used above counters or within wall units. Fittings that allow the door to retract further into the cabinet than the ALTST20-D10 series support applications where full front access is valuable, such as equipment bays or work areas that need an unobstructed opening.
How System Adjustments Support Repeatable Results
The door alignment adjustability built into this overlay pocket door system allows fine correction of the door position relative to the cabinet face, which helps produce consistent reveals across a run of cabinets. An overlay amount of up to 3/8 inch (10 mm) gives a defined design envelope, so repeated door sizes and overlay relationships can be maintained from cabinet to cabinet. The overlay damper unit with an adjustment screw provides a specific adjustment point for damping action, which lets the installer tune closing behavior across multiple doors for a uniform feel. Using two slides to guide the door creates a defined travel path, helping align motion characteristics between cabinets using the same ALT-ST15-D10M-16 pocket door hardware.
Common Questions About ALT-ST15-D10M-16 Pocket Door
What cabinet depth does this overlay pocket door kit require?
The overlay pocket door kit is specified for a minimum cabinet depth of 16-9/16 inches, which sets the case dimension needed for the door to retract properly inside the cabinet.
What door height range does the Sugatsune system support?
The Sugatsune overlay pocket door system is designed for door heights from 27-9/16 inches to 35-7/16 inches, aligning it with common medium-height cabinet doors used in storage and multimedia applications.
How much overlay does the ALT-ST15-D10M-16 kit allow?
The ALT-ST15-D10M-16 overlay pocket door kit allows an overlay amount of up to 3/8 inch, or 10 mm, which defines how far the door can overlap the cabinet opening.
What is the benefit of the overlay damper unit with adjustment screw?
The overlay damper unit on this system has an adjustment screw, giving a built-in point to adjust damping performance so door motion can be tuned during installation work.
How does this kit compare to the ALTST20-D10 series for retraction?
This overlay pocket door system uses fittings that allow the door to retract further into the cabinet than the ALTST20-D10 series, opening more of the cabinet front for access.
Why are two slides specified for this pocket door hardware?
The pocket door hardware specifies two slides, so both sides of the door run on guided tracks, supporting stable, controlled travel as the door moves in and out of the cabinet.
Selecting This Overlay Pocket Door Hardware For Your Build
This overlay pocket door kit from Sugatsune America combines defined geometry, an overlay amount of up to 3/8 inch (10 mm), and door alignment adjustability, giving clear design and tuning parameters for cabinet projects. The specified door height range of 27-9/16 inches to 35-7/16 inches and the minimum cabinet depth of 16-9/16 inches help match this ALT-ST15-D10M-16 pocket door hardware to medium-size cases where doors need to retract fully. For projects calling for pocket door slides that retract further than the ALTST20-D10 series, this system offers fittings tailored to that role. Put these verified dimensions and adjustments to work on the next cabinet run that needs clean overlay fronts with doors that disappear into the case.