10 inch RV723 extra heavy duty wood shelf bracket describes a Reeve Store Equipment Company bracket designed to support wood shelving where high load capacity is required, so installers can build stronger storage runs in closets, garages, and commercial layouts. The bracket is part of the Reeve Model RV723 line, so it fits into a consistent shelving standard system that is familiar on many professional jobs. This specific model uses a right flange configuration, so it works on the right side of a wood shelf when paired with matching center or left flanges in the same series. The satin zinc finish, described as Brillatone (zinc), gives the tempered steel a bright, clean appearance that coordinates with common closet and storage hardware. Material thickness of .085 inch tempered steel gives the bracket its extra heavy-duty classification, so installed shelving can handle demanding loads when bracket spacing and shelf material follow typical trade practice.
This RV723 bracket is typically used with the RV700 series standard, so it integrates into the vertical track system specified by the same manufacturer for adjustable shelving layouts. The two engagement teeth locate in the RV700 standard slots, so the bracket shoulders carry the vertical load directly into the steel standard. The additional stabilizer tooth reduces sway, so the bracket feels solid when loading and unloading shelves along the row. Keyhole slots in the flange line up along the top of the bracket, so wood shelves can be positioned, marked, and fastened in a repeatable pattern from bracket to bracket. The right flange designation means this bracket supports the right side of the shelf when viewed from the front, so installers can match it with center or left flange versions where the shelving design calls for them.
The 10 inch length identified for this RV723 model suits wood shelves designed around that projection, so closets or storage bays can be laid out with predictable shelf depths. The bracket is one of several available lengths in the RV723 series, which also offers 12, 14, 16, 18, 20, and 22 inch versions, so installers can keep the same bracket family across shallow and deep shelving in a project. Because the bracket is typically used with the RV700 series standard, it is suited to wall-mounted track systems where vertical standards are anchored and brackets are adjusted for shelf height. The extra heavy-duty classification, backed by a 230-520 lb per pair rating depending on bracket length, means this 10 inch size works in higher-load applications relative to light-duty closet brackets when the shelf dimensions and spacing work within that length range. The satin zinc Brillatone finish visually matches other zinc-coated standards and components in the Reeve system, so bracket rows along RV700 standards maintain a consistent appearance.
The use of .085 inch thick tempered steel across the RV723 line gives this 10 inch bracket the stiffness needed to hold its angle under load, so shelves remain level when stocked with heavier items appropriate to the published rating range for the pair. The two engagement teeth are designed to seat fully into the RV700 series standard, so each bracket locks into a defined position, which keeps shelf levels consistent from upright to upright. The stabilizer tooth works with those engagement teeth to reduce sway, so the bracket resists side-to-side movement that could otherwise loosen fasteners or cause shelves to shift. Keyhole slots in the flange allow the shelf to be mounted to the bracket with a slide-down motion, so installers can pre-position screws in the shelf and then set the shelf onto all the brackets in a run, which speeds large repetitive installations. The right flange type is one of three flange options in the RV723 family - left, right, and center - so the system can support continuous shelving where different flange positions are needed along a span while keeping all brackets within the same RV723 and RV700 ecosystem.
The RV723 bracket uses .085 inch thick tempered steel and carries a 230-520 lb per pair rating based on length, so it supports heavier shelving loads than typical light-duty brackets.
The 10 inch RV723 bracket is typically used with the RV700 series standard, so it fits into that vertical track system when planning adjustable shelf layouts.
The right flange design positions this bracket on the right side of the shelf, so it is matched with left or center flange RV723 brackets to support full-length runs.
The flange keyhole slots allow shelves to be dropped onto pre-positioned fasteners, so installers can set multiple brackets under a shelf and secure it quickly along the RV700 standards.
The two engagement teeth and stabilizer tooth lock the bracket into the RV700 standard and reduce sway, so the shelf support feels solid under everyday loading and unloading.
The RV723 series offers 10, 12, 14, 16, 18, 20, and 22 inch lengths, so shelf depth can be matched to these bracket sizes when laying out storage or closet systems.
The Reeve Model RV723 10 inch extra heavy-duty wood shelf bracket in satin zinc is built around .085 inch thick tempered steel, a 230-520 lb per pair rating based on length, and a right flange that ties into the RV700 series standard. Those verified details let you plan closet, garage, or commercial shelving knowing the bracket family, finish, and load rating are defined. For projects already using RV700 standards or specifying RV723 components, this 10 inch right flange bracket matches that system so shelf depth, vertical adjustment, and visual appearance all stay consistent from one run to the next.
Sold In: 1 Each
