S6 Camfix Side Entry Fastener For 18/19mm Panels
S6 CAMFIX 18/19MM side entry is a Titus Tool cam housing designed for 18/19 mm (3/4 inch) panels, so it matches common case and cabinet material thickness on production jobs. As a SYS 6 housing in almond, it blends with light-colored panel finishes where visible fittings need a closer color match. This camfix fastener sits in the panel edge as a side entry housing, creating a ready-to-assemble joint that suits RTA and system fitting work. The design fits the RTA and system fittings category, so it ties into typical knock-down cabinet and furniture assemblies used in shops and on site. As part of the Fasteners and RTA Fittings range, it supports repeatable joints where multiple identical units are built for contract or commercial runs.
Camfix Features That Support Production Work
- The linear cam design delivers constant tightening loads when driving, so joints pull together consistently across a run of cabinets, reducing variation between units on high volume production jobs.
- The Angledrive feature on the cam is built for maximum driving comfort, which lets installers drive the cam from a better angle in tight interiors and speeds up assembly on repetitive RTA work.
- Availability for 18/19 mm (3/4 inch) panels means the housing fits standard 3/4 inch material, helping maintain predictable bore patterns and edge distances on typical cabinet carcasses.
- Being suitable for use in high volume production aligns this housing with line-boring and CNC workflows, where the same drilling pattern is repeated across many panels every shift.
- The option of economical non-outrigger style or outrigger style with easy alignment and added strength allows shops to choose between lowest cost or extra locating stability for loaded casework.
Installation Details For SYS 6 Cam Housing
This SYS 6 housing can be machine inserted, so it integrates into automated insertion lines or CNC drilling and inserting centers handling RTA fittings. The same housing can also be knocked in with a hammer, giving flexibility for smaller shops or on-site assembly where powered insertion equipment is not in use. Recommended boring bits for non-outrigger cams are AA203201 13/16 inch RH boring bits, tying the bore size directly to the housing diameter. For outrigger cams, recommended bits AA201010 and AA203201 in 3/8 inch and 13/16 inch RH sizes define both pilot and main bore dimensions, supporting accurate drilling setups. These matched boring bit part numbers give a direct reference for setting up drill heads or CNC tooling lists around this camfix system.
Using S6 Camfix Housings In Cabinet Runs
Where This SYS 6 Housing Fits Best
This SYS 6 housing is intended for RTA and system fittings, so it suits frameless cabinets, case goods, and modular components built from 18/19 mm (3/4 inch) material. Its role as a fastener in the RTA fittings category makes it a natural fit in flat-pack cabinet runs where joints must pull tight after boring and transport. The almond color works well with light laminates and melamine, so visible panel edges or interior joints maintain a coordinated appearance on finished jobs. Because it is ideal for use in high volume production, it supports factories and busy shops running repeated carcass patterns, where the same cam housing is used throughout a line. The choice between non-outrigger style as the most economical option and outrigger style for easy alignment and added strength lets designers tune each joint style to the load and visibility of that cabinet area.
Details That Help Repeatable Joint Results
The linear cam design provides constant tightening loads while driving, so each turn of the driver pulls components together with predictable force and reduces the likelihood of under- or over-tightened RTA joints. This consistency is valuable on large orders where many installers assemble units, because the cam behavior stays the same from cabinet to cabinet. The Angledrive feature on the cam improves driving comfort by allowing better driver access, especially inside deep cases or near corners, helping maintain speed when access is restricted. Machine insertion capability lets production lines press this cam housing into pre-bored holes during a single pass, shortening handling time and keeping hole-to-cam fit reliable. Hammer knock-in capability supports field or small-shop assembly using the same cam housing pattern, so panels drilled in a factory can be assembled or finished later without specialized insertion equipment. Clear boring bit references - AA203201 13/16 inch RH for non-outrigger cams, and AA201010 3/8 inch plus AA203201 13/16 inch RH for outrigger cams - tie the drilling pattern directly to cam size, which helps maintain bore accuracy and reduces rework on mis-sized holes.
Common Questions About S6 Camfix 18/19mm Side Entry
What panel thickness is this SYS 6 housing designed for?
The S6 CAMFIX housing is available for 18/19 mm, or 3/4 inch, panels, so it matches standard cabinet carcass and shelf material commonly used in frameless and modular construction.
How is the S6 CAMFIX housing installed in production?
The S6 CAMFIX housing can be machine inserted, allowing it to be pressed into pre-bored holes on automated or CNC-based lines that handle RTA fittings.
Can the SYS 6 housing be installed without machines?
The SYS 6 housing can be knocked in with a hammer, so installers and smaller shops can seat the cam housing in bored holes using hand tools during assembly.
Which boring bits match the non-outrigger S6 CAMFIX style?
The non-outrigger cam style uses recommended boring bit AA203201 in a 13/16 inch right-hand size, aligning the drilling diameter to the cam housing for proper fit.
What boring bits are recommended for outrigger S6 cam housings?
For outrigger cam styles, recommended bits are AA201010 3/8 inch right-hand and AA203201 13/16 inch right-hand, which define the pilot and main bores for accurate drilling.
How does the linear cam design affect joint performance?
The linear cam design provides constant tightening loads when driving, so each joint pulls together with steady force, supporting consistent RTA connections across multiple assemblies.
Choose S6 Camfix Housing For RTA Panel Work
The S6 CAMFIX 18/19MM side entry housing in almond ties directly into RTA and system fittings for 18/19 mm (3/4 inch) panels, delivering constant tightening loads with its linear cam design. Angledrive cam geometry and options for non-outrigger or outrigger styles support both economical and strengthened joints on cabinet carcasses. With clear boring bit references for both styles and the flexibility of machine insertion or hammer knock-in, this Titus Tool SYS 6 housing offers a defined path from drilling pattern to assembly. Select this part when production or installation workflows rely on repeatable cam-driven joints in 3/4 inch panel construction.
