Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
The Würth #5 x 11.5mm Flat Head Euro Screw is a coarse-thread, line-bore fastener designed to mount European cup hinges, drawer slides, and other 32mm system hardware to cabinet panels. The 11.5mm length seats securely in standard 5mm line-bore holes without over-penetrating typical panel stock, making it a practical choice for frameless and face-frame cabinet installation.
Euro screws are the standard fastener for attaching hardware mounting plates to the 5mm line-bore holes drilled into cabinet sides and floors. At 11.5mm, this screw has enough shank length to pass through the mounting plate and thread fully into panel material, locking the hardware in place without needing a separate anchor. It suits European cup hinges from Blum and similarly spec'd hardware lines, as well as drawer slide mounting clips and shelf pin hardware that use the same 32mm hole pattern. The blunt point relies on the pre-bored hole to start, so installation is clean and consistent when the panel has been properly line-bored.
The nickel finish keeps the screw visually low-profile against the light interiors of melamine and white-laminated cabinets. Coarse threading is matched to the engineered panels that dominate cabinet manufacturing: particleboard, MDF, and melamine-faced substrates all hold a coarse thread well in the pullout direction. The 7.2mm flat head is sized to seat in the countersunk holes of standard European hardware mounting plates, so the head sits flush rather than proud once fully driven.
Cabinet shops running production work on frameless or face-frame boxes benefit from having a dedicated euro screw rather than improvising with a general-purpose fastener. The consistent 11.5mm length and PZ2 drive let installers move through hinge and slide mounting quickly without adjusting bit depth or swapping drivers. Kitchen and bath installers doing on-site hardware replacement find the same advantage: the right screw in the right hole, driven with the bit already on the gun. A box of 1000 supports both shop production and a busy install schedule without frequent reordering.
Euro screws are installed into pre-bored 5mm line-bore holes, not driven directly into undrilled material. The blunt point is designed to enter that prepared hole cleanly and begin threading without the splitting risk that a sharp point can introduce when driven into a hole that is already close to the screw's shank diameter.
A PZ2 Pozidriv bit has parallel flanks that resist cam-out under torque, while a Phillips bit has tapered flanks that tend to rise out of the recess when driving force increases. For repetitive hardware installation where screws are driven to a consistent depth, the Pozidriv drive holds the bit more reliably and reduces head damage.
Yes. This screw is specified for use with Blum hardware. Blum cup hinges and drawer slides mount through holes in their plates that accept a #5 euro screw, and the 7.2mm flat head seats in the countersunk opening of those plates.
Yes. The 11.5mm thread length engages well within 19mm panel stock. The screw reaches into the panel without approaching the far face, which matters for panels where a through-penetration would be visible or would compromise the surface.
Euro screws are engineered primarily for engineered panel materials. In solid wood, the coarse thread still functions, but the pre-bored hole must be sized accurately for the screw's shank to prevent splitting. Most 32mm system installations are in panel-based cabinets, where this screw performs as intended.
A hinge or slide is only as reliable as the screw holding its mounting plate. This Würth euro screw gives cabinet builders and installers a dedicated, correctly sized fastener for 32mm system work, so hardware stays aligned and tight across the life of the cabinet.
Sold In: 1000 Each
Quantity | Unit Price | Catalog | ||||
|---|---|---|---|---|---|---|
Sold in: 1000 Each |  WW59920 Mfr# 027610575 961 1000 | Würth #5 x 7.5mm Flat Head Euro Screw Pozidriv Drive - Blunt Point Coarse Thread Nickel, 027610575 961 1000 - 1000/Box | ||||
Sold in: 10 Each |  WW614176652 Mfr# 0614176652090 10 | #2 x 1" Pozidriv Insert Bit (10/Box) | ||||
Sold in: 1000 Each | WW60000 Mfr# 027610510 961 1000 | Würth #5 x 10mm Flat Head Euro Screw Pozidriv Drive - Blunt Point Coarse Thread Nickel, 027610510 961 1000 - 1000/Box | ||||
Sold in: 1000 Each | WW60200 Mfr# 027610513 961 1000 | Würth #5 x 13mm Flat Head Euro Screw Pozidriv Drive - Blunt Point Coarse Thread Nickel, 027610513 961 1000 - 1000/Box | ||||
Sold in: 1000 Each | WW60300 Mfr# 0276105145961 1000 | Würth #5 x 14.5mm Flat Head Euro Screw Pozidriv Drive - Blunt Point Coarse Thread Nickel, 0276105145961 1000 - 1000/Box | ||||
Sold in: 1000 Each |  WW60520 Mfr# 027610525 961 1000 | Würth #5 x 25mm Flat Head Euro Screw Pozidriv Drive - Blunt Point Coarse Thread Nickel, 027610525 961 1000 - 1000/Box |