Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Berenson Square Series 128 mm pull gives you a polished chrome handle sized for standard cabinet layouts, so aligning multiple pulls across doors and drawers stays consistent on the job. This pull is made from zinc die cast, which provides a solid metal feel that holds up to repeated daily use in kitchen or shop environments. The polished chrome finish reflects surrounding surfaces, tying into other chrome hardware for a unified look. With a 5-3/4 inch overall length, this pull spans a visible portion of the front without overpowering narrower drawer faces. The 5-1/16 inch center to center dimension matches common drilling patterns, which supports straightforward layout on cabinet runs. A 1-3/16 inch projection gives usable hand clearance from the door face, helping fingers grab comfortably from the front. The 1/2 inch width presents a clean square profile that reads modern and lines up well with flat-panel fronts.
This Berenson polished chrome cabinet pull uses a 5-1/16 inch center to center dimension, so hole drilling can follow a repeatable pattern across a full installation. The 5-3/4 inch length helps place mounting points near the ends, giving the pull a balanced stance on wider drawer fronts. With a 1-3/16 inch projection, the handle stands off the face enough to clear door edges and trim in typical cabinet layouts. The 1/2 inch width keeps the footprint narrow, which is useful when aligning multiple pulls in close proximity on smaller drawer stacks. These fixed dimensions give installers clear reference points for jigs, templates, and layout marks.
This Square Series 5-1/16 inch pull works well on cabinet doors and drawers that call for a straight, square profile in polished chrome. The 5-3/4 inch overall length allows the pull to sit proportionally on standard base cabinets and wall cabinets, bridging enough of the panel to be easy to grab. On drawer banks, the 128 mm center to center spacing matches common pre-set boring patterns, supporting alignment across stacked fronts. The polished chrome finish coordinates with chrome faucets, hinges, and other decorative hardware, tying the room together visually. Zinc die cast construction suits busy kitchen and shop spaces where pulls are handled many times a day.
The 5-1/16 inch center to center size lets installers use the same drilling reference across multiple fronts, which reduces layout time and keeps lines straight from cabinet to cabinet. Because the overall length is only slightly greater than the drilling dimension, the pull positions its mounting points near the ends, which gives a stable feel when pulling from either side. The 1-3/16 inch projection sets the grip off the surface at a practical distance, which helps avoid knuckles rubbing the door face while still keeping the pull close enough for tight spaces. The 1/2 inch width and square form simplify alignment with door edges or drawer rails, helping achieve clean sight lines. Together, these measurements support efficient use of templates and jigs, cutting down on rework during larger hardware runs.
The Berenson 9285-1026-C pull has a 5-1/16 inch center to center, 5-3/4 inch overall length, 1-3/16 inch projection, and 1/2 inch width, which guides drilling and layout.
The Square Series 128 mm pull is zinc die cast, which provides a solid metal body that stands up to frequent cabinet door and drawer use.
This Berenson cabinet pull has a polished chrome finish, which matches other chrome hardware and fixtures for a coordinated cabinet installation.
The 5-1/16 inch center to center spacing provides a standard drilling measurement, which supports consistent hole placement across multiple doors and drawers.
The 1-3/16 inch projection sets the pull away from the surface, providing finger clearance that helps grip doors and drawers comfortably.
The 1/2 inch width gives a slim square profile, which supports a clean, modern line on flat-panel cabinet doors and drawer fronts.
The Berenson Square Series 5-1/16 inch center to center polished chrome pull brings defined dimensions and a zinc die cast build to cabinet projects, which supports precise drilling and a solid feel on doors and drawers. Its 5-3/4 inch length and 1/3-16 inch projection work together to balance appearance and hand clearance across typical kitchen, bath, or shop layouts. With a 1/2 inch wide square profile in polished chrome, this pull aligns with modern cabinet styles while matching other chrome hardware in the space. For installers and fabricators planning consistent hardware runs, these fixed measurements help streamline layout and repeat the same look from cabinet to cabinet.
Sold In: 1 Each
