Berenson Square Series 3-3/4" (96 mm) Center to Center Dull Chrome Pull, - 9289-10DC-C

Berenson Square Series Dull Chrome Pull Use

Berenson Square Series dull chrome pull gives a cabinet or drawer a straight, square look, which suits projects where clean lines and simple geometry keep fronts visually organized. The 3-3/4 inch (96 mm) center to center layout sets drilling points on a standard mid-size spread, helping installers line up with common cabinet boring patterns. A total length of 4-1/2 inch leaves slight overhang past the screw centers, which visually balances the pull on doors and drawers without crowding smaller fronts. The 1-3/16 inch projection stands the handgrip off the face, providing finger clearance that helps with quick opening, especially on heavier fronts. A width of 7/16 inch creates a slim front profile, so the pull reads light on the face while still giving a defined edge to grab.

Key Square Series Pull Details For Projects

• The Square collection design keeps the pull profile straight and squared, which works well when cabinets use flat panels or slab fronts and installers want hardware that visually follows those lines.
• Zinc die cast construction forms the pull as a solid metal piece, which supports repeatable sizing across a job and gives a consistent feel from door to door on the same run.
• The dull chrome finish creates a muted metallic surface, which can help the pull blend with brushed fixtures and keep reflections low across banks of doors in brighter rooms.
• A center to center of 3-3/4 inch (96 mm) matches a common drilling dimension, which simplifies layout when replacing existing pulls made on that spread across an installed kitchen or shop cabinet line.
• The 4-1/2 inch overall length adds a small visual margin beyond the screw centers, which helps the pull sit proportionally on medium-width doors and typical drawer fronts without running edge to edge.
• A 1-3/16 inch projection stands the gripping surface off the cabinet face, which provides working finger clearance while still keeping the pull tight enough to the door for narrow walkways.

Center To Center And Size Details For Fit

The 3-3/4 inch (96 mm) center to center spacing defines the hole layout for this Berenson Square Series pull, which guides drilling or boring jigs whenever fronts are prepared before finishing. With a total length of 4-1/2 inch, the pull will extend slightly beyond the hole pattern, helping it cover the boring neatly while leaving some standoff from adjacent hardware on narrow rails. The 7/16 inch width limits the visual footprint on the face, which is useful when multiple pulls sit close together on stacked drawers. A 1-3/16 inch projection sets how far the handgrip stands off the surface, which affects how easily fingers can wrap behind the pull when doors are flush with nearby cabinets.

How This 9289-10DC-C Pull Works In Use

Square Series Pull On Cabinets And Drawers

This pull is identified as part of the Square collection, which applies a straight-line, right-angled profile across its length and suits cabinet faces that repeat that geometry. The 3-3/4 inch (96 mm) center to center dimension places the mounting points at a size that often fits many mid-width cabinet doors, so one pull can serve both uppers and base units. At 4-1/2 inch overall length, the handle leaves a modest span beyond the mounting holes, which helps it sit centered on drawer fronts that are not overly wide while still looking substantial on tall doors. The 7/16 inch width keeps the hardware visually light, useful when cabinets carry several pulls in a vertical stack.

Details That Support Consistent Pull Alignment

The zinc die cast material allows this pull to be manufactured with consistent dimensions from piece to piece, which supports straight visual alignment when runs of doors use multiple pulls. The 1-3/16 inch projection sets a fixed offset from the cabinet face, helping rows of handles stand out an equal distance for a uniform look along long banks of cases. The dull chrome finish gives the surface a subdued metallic sheen, which reduces visible fingerprints compared to high-gloss metal and helps installations maintain an even appearance across regularly handled fronts. With the manufacturer part number 9289-10DC-C and the SAP description specifying a Square pull at 96 mm center to center in dull chrome, ordering repeat quantities for later phases of a project ties directly back to the same size and finish for consistent hardware across all installed cabinetry.

Common Questions About This Berenson Square Pull

Choose This Pull For 96 mm Layouts

The Berenson Square Series dull chrome pull with 3-3/4 inch (96 mm) center to center delivers a straightforward, square profile that lines up with standard boring dimensions. When a project calls for a 4-1/2 inch long, zinc die cast handle in a muted chrome finish, this 9289-10DC-C model provides the specific size, projection, and width needed to keep cabinet runs consistent from one door or drawer front to the next.