Berenson Square Series 3-3/4" (96 mm) Center to Center Brushed Nickel Pull, - 9287-1BPN-C

Berenson Square Series 96 Mm Pull For Cabinets

Berenson Square Series 96 mm pull gives cabinets a straight, square profile that suits projects where clean lines matter. The pull is made from zinc die cast, so it provides a solid metal feel that supports regular cabinet use. Its brushed nickel finish softens reflections, which helps doors and drawers blend with other brushed nickel hardware in the same space. The pull has a 3-3/4 inch center to center dimension, allowing it to align with common drilling patterns on many cabinet fronts. Overall length of 4-1/2 inches extends slightly beyond the mounting holes, giving visual balance at each end. A projection of 1-3/16 inches creates hand clearance between the fingers and the cabinet face during opening. The 7/16 inch width presents a narrow front edge, which suits installations where a slimmer pull profile is preferred.

Key Details That Support Cabinet Projects

• The Square Series design provides straight, squared edges, which suits cabinet layouts built around modern, linear fronts where decorative curves are not desired.
• A 3-3/4 inch center to center dimension lines up with a common boring pattern, helping the pull fit many predrilled fronts in kitchen, bath, or shop cabinets.
• Overall length of 4-1/2 inches leaves a small overhang at each side of the mounting holes, creating a balanced look on doors and drawers of varied widths.
• The 1-3/16 inch projection positions the grip away from the cabinet face, supporting finger clearance so doors and drawers can be opened without knuckles rubbing.
• A 7/16 inch width keeps the pull visually slim, which matches lighter drawer faces or narrow rails where a bulky handle might look oversized.
• The brushed nickel finish matches other brushed nickel components, allowing the pull to integrate into projects that already use similar finishes across the room.
• Zinc die cast construction forms a rigid pull body, supporting repeated opening and closing cycles on frequently used cabinet fronts.

Installation And Fit Details For This Pull

This Berenson Square Series pull uses a 3-3/4 inch center to center layout, so the mounting holes align on a straight line that matches many standard drilling jigs. The 96 mm spacing works in both metric and inch-based layouts, which helps when cabinets are bored using either system. With a projection of 1-3/16 inches, the pull stands off the door face at a depth suitable for typical cabinet fronts, giving space for fingers even on thicker door designs. The 4-1/2 inch overall length allows the pull to sit comfortably on both narrow and wider drawer fronts, so one part number can serve multiple cabinet sizes in the same installation.

Using This Brushed Nickel Pull In Real Work

Where The 96 Mm Cabinet Pull Fits Best

The Berenson Square Series 96 mm pull works wherever a 3-3/4 inch center to center handle is planned, so it can serve on both new cabinet builds and hardware refresh jobs using that pattern. Its brushed nickel finish supports projects that rely on muted metal tones, which is useful in kitchens, baths, or office cabinetry using similar faucet and hinge finishes. The 4-1/2 inch overall length allows the pull to sit on doors or drawers without dominating the front, so it suits wall cabinets and base cabinets alike. Because the pull uses zinc die cast construction, it provides a solid feel that supports cabinets in high-use areas such as workrooms or kitchen prep zones. The 7/16 inch width pairs well with narrow stiles, helping maintain visual proportion on smaller doors that share the same handle style as wider drawers.

Details That Support Consistent Mounting Results

The 3-3/4 inch center to center dimension on this pull gives installers a predictable measurement for drilling, which helps maintain alignment across long cabinet runs. Since 96 mm spacing corresponds closely with 3-3/4 inches, it works with metric or imperial layout tools, which simplifies work when mixed measurements appear on a job. The 1-3/16 inch projection sets a repeatable stand-off distance from the cabinet face, so all doors and drawers align visually when viewed down a row. Its brushed nickel finish keeps fingerprints less pronounced than a highly polished surface, which supports a clean appearance across frequently handled fronts. Zinc die cast construction helps maintain the pull shape under everyday loading, so hardware on multiple cabinets feels consistent over time. Combined, these details help cabinet runs share the same look and function from one end of the installation to the other.

Common Questions About This Berenson Cabinet Pull

Select This Pull For 96 Mm Cabinet Layouts

The Berenson Square Series 96 mm pull combines a 3-3/4 inch center to center layout with zinc die cast construction and brushed nickel finish, so it suits cabinet runs built around that spacing. Its 4-1/2 inch length, 1-3/16 inch projection, and 7/16 inch width give a consistent look and comfortable grip across doors and drawers using the same handle style. For projects that rely on square-edge hardware in a brushed nickel tone, this pull offers a defined set of dimensions that support repeatable results from one cabinet front to the next.