Berenson Square Series 2-1/2" (64 mm) Center to Center Brushed Nickel Pull, - 9290-1BPN-C

Berenson Square Brushed Nickel Pull For Cabinets

Berenson Square brushed nickel pull is a zinc die cast cabinet handle from the Berenson Square collection that provides a consistent look across banks of doors and drawers. The 2-1/2 inch (64 mm) center to center drilling positions mounting holes for common cabinet layouts, which helps installers line up multiple pulls in a straight visual run. The brushed nickel finish diffuses light along the 3-1/8 inch overall length, reducing harsh reflections on cabinet faces. A 1-3/16 inch projection sets the grip away from the door surface, giving fingers clearance while reducing snag points in tight walkways. The 3/8 inch width presents a slim front profile, which helps this pull sit neatly on narrow rails or smaller drawer fronts. As part of the Handles and Pulls class from Berenson Corporation, this pull fits decorative hardware projects that call for a square, modern shape.

Key Details Of This Square Cabinet Pull

• The Square collection identity ties this pull to a defined geometric style, so installers can repeat the same look across different cabinet runs without mixing shapes.
• The zinc die cast material creates a solid, uniform body, which supports repeatable drilling and mounting because each pull matches the next in shape.
• The brushed nickel finish establishes a muted metallic appearance, helping the pull sit comfortably with many hinge and faucet finishes on the same project.
• The 3-1/8 inch overall length gives a compact handle span, which works well on narrower doors or drawers while still offering a full hand contact area.
• The 2-1/2 inch (64 mm) center to center size matches a common drilling pattern, simplifying layout when replacing existing pulls with the same hole spacing.
• The 1-3/16 inch projection holds the grip away from the cabinet face, providing room for fingers to pull doors and drawers open without contacting the surface.
• The 3/8 inch width keeps the pull visually light, which can help maintain clean lines on modern cabinet designs with slim face frames.

Mounting And Fit Details For This Pull

This 64 mm center to center cabinet pull uses two mounting points set 2-1/2 inches apart, so hole locations transfer easily from shop jigs or existing fronts with that pattern. The 3-1/8 inch overall length leaves minimal overhang past the mounting centers, which is useful on narrow drawer fronts where longer hardware could crowd edges. With a 1-3/16 inch projection, the pull stands out enough for a comfortable grip while keeping the handle close to the cabinet plane, which is helpful around appliances and walkways. The 3/8 inch width concentrates the pull's bearing surface in a slim bar, so it can sit cleanly on face-frame stiles and slab doors without covering too much wood or laminate.

Using This Berenson Pull In Cabinet Projects

Where This Brushed Nickel Pull Fits Best

This Berenson Square Series zinc die cast pull fits cabinet, drawer, or door fronts drilled at 2-1/2 inches (64 mm) center to center, aligning with a widely used spacing in residential and light commercial casework. The 3-1/8 inch length makes it suited to smaller cabinet doors, bath vanities, or compact kitchen drawers where a larger pull might dominate the front. Its 1-3/16 inch projection allows comfortable gripping on thicker fronts because the handle stands off the surface enough for fingers to wrap behind. The 3/8 inch width offers a narrow bar profile that visually suits flat-panel or square-edged doors, supporting a consistent linear look across upper and lower cabinets.

Details That Support Consistent Installation Results

The defined 64 mm (2-1/2 inch) center to center dimension lets installers use standard drilling jigs, which speeds repetitive mounting on multi-cabinet runs and helps keep hardware lines straight. The zinc die cast construction keeps the pull's geometry consistent from piece to piece, so once a jig or template is dialed in, each additional installation matches the last. The brushed nickel finish on the Square collection pull masks minor fingerprints and handling marks during installation better than highly polished surfaces, which supports a clean final appearance. Its 3-1/8 inch overall length and compact footprint simplify layout on narrow rails because the handle will not extend excessively past the mounting holes, helping maintain balanced reveals at door edges.

Common Questions About This 64 Mm Cabinet Pull

Select This Pull For 64 Mm Cabinet Layouts

The Berenson 9290-1BPN-C Square Series brushed nickel zinc die cast pull pairs a 2-1/2 inch (64 mm) center to center drilling with a compact 3-1/8 inch length, fitting cabinets that use this common spacing. Its 1-3/16 inch projection and 3/8 inch width create a practical grip profile that sits neatly on narrow or full-overlay fronts. For cabinet runs designed around a square, linear hardware look in brushed nickel, this pull offers defined dimensions that support consistent layout across doors and drawers.