Berenson Dual Series 5-1/16" (128 mm) Center to Center Dull Chrome Pull, - 9310-10DC-C
Description
Berenson Dual Series 128mm Pull For Cabinets
Berenson Dual Series 128mm pull gives you a defined hand grip with a 5-1/16 inch center to center dimension, so it lines up well on cabinets and drawers planned around common 128 mm drilling patterns. The zinc die cast material provides a solid, weighty feel in the hand, which helps doors and drawers open in a controlled way during daily use. A 5-3/8 inch overall length offers a little extra bar beyond the 128 mm centers, giving fingers room at each end when grabbing from different angles. The dull chrome finish keeps reflections down compared to bright chrome, which helps this pull sit quietly on the face of the cabinet while still reading as a clean metallic accent. A 1 inch projection stands the pull off the surface enough for fingers to wrap behind it, supporting a consistent grip across doors and narrower drawer fronts.
Key Details That Support Cabinet Work
- The 5-1/16 inch center to center measurement matches standard 128 mm boring, which simplifies layout and speeds repeat drilling across door and drawer runs.
- The zinc die cast construction delivers a uniform, rigid pull body, which supports straight alignment when tightening to the front of the cabinet.
- The dull chrome finish keeps glare down compared to high-polish chrome, which helps the hardware read consistently under varied shop and room lighting.
- The 5-3/8 inch overall length gives a bit of bar past the screw locations, which provides comfortable grip space for different hand positions.
- The 1 inch projection creates stand-off from the door or drawer face, which helps fingers clear the surface without scraping finished fronts.
Cabinet Pull Dimensions That Guide Installation
The 5-1/16 inch center to center dimension defines where holes need to be drilled, so jigs can be set for 128 mm spacing and used repeatedly across a job. With a 5-3/8 inch overall length, the pull has modest overhang beyond the mounting points, which helps when aligning it visually to door stiles or drawer edges. The 3/8 inch width concentrates the pull into a slim bar, which leaves more of the door or drawer face visible while still providing a defined gripping edge. A 1 inch projection sets the pull off the surface just far enough for fingers to hook behind, supporting smooth opening on thicker door profiles and standard drawer fronts.
Using This Dull Chrome Berenson Pull In Projects
Where This Zinc Die Cast Pull Works Well
The Berenson Dual Series 5-3/8 inch length and 5-1/16 inch center to center layout fit well on typical cabinet doors and mid-width drawers, so it can carry through a full kitchen or shop run without changing drilling patterns. The 128 mm spacing suits European-influenced layouts that standardize on metric hardware, which helps align this pull with existing boring equipment and templates. Its 3/8 inch width keeps the profile slim, making it suitable for face-frame or frameless cabinetry where hardware should stay visually light. The 1 inch projection gives enough clearance for fingers even on doors with applied moldings, supporting consistent operation across different cabinet styles built around the same pull.
Details That Support Repeatable Cabinet Results
The defined 5-1/16 inch center to center measurement lets installers set stops on jigs once and repeat hole drilling, which cuts layout time and helps keep pulls straight across large banks of drawers. The zinc die cast material provides dimensional consistency from pull to pull, supporting even reveals and alignment when hardware is ganged along a tall pantry or wide drawer stack. With a 5-3/8 inch overall length, pulls can bridge typical drawer rail spacings cleanly, which helps maintain visual rhythm on modular cabinetry. The dull chrome finish gives a muted metallic look that reads the same across multiple pieces, which supports a uniform appearance when hardware is installed throughout a room or project.
Common Questions About This Berenson Cabinet Pull
What is the center to center size on this pull?
The Berenson Dual Series pull has a 5-1/16 inch center to center dimension, so hole spacing matches standard 128 mm cabinet boring patterns during installation.
How long is the Berenson Dual Series 9310-10DC-C pull?
The pull has a 5-3/8 inch overall length, which provides a bit of bar beyond the mounting points for a comfortable grip on doors and drawers.
What material is used for this dull chrome cabinet pull?
This pull is made from zinc die cast, giving a solid feel and consistent dimensions that support straight, repeatable hardware alignment.
How far does this cabinet pull project from the door or drawer?
The pull projects 1 inch from the surface, providing finger clearance behind the bar for easy opening without crowding the door face.
What is the finish on the 9310-10DC-C Berenson pull?
The pull has a dull chrome finish, giving a muted metallic look that reduces glare compared to bright chrome on cabinet fronts.
How wide is the bar on this Berenson cabinet handle?
The bar width is 3/8 inch, creating a slim profile that leaves more of the cabinet front visible while still offering a defined gripping edge.
Selecting This Pull For Consistent Cabinet Layouts
The Berenson Dual Series 5-1/16 inch center to center dull chrome pull combines 128 mm spacing, 5-3/8 inch length, and 1 inch projection, so drilling patterns, grip clearance, and visual alignment stay consistent from cabinet to cabinet. The zinc die cast construction and 3/8 inch width support a slim, uniform profile that works across doors and drawers planned around this hardware family.
