Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
The GSlide G-Slide series 20 inch over-travel side-mount ball bearing drawer slide is built for installations where the cabinet sits beneath a countertop overhang or a deep face frame. Rated 90 lb per pair, it carries the drawer 1 inch past full extension so the back of the box clears the obstruction and stays reachable.
A standard full-extension slide brings the drawer to the cabinet face, but that is exactly where a countertop overhang or a thick face frame starts blocking access. The G-Slide over-travel action pushes the drawer box 1 inch past that point, so rear contents are fully exposed rather than partially hidden behind the lip. This matters most in base cabinet runs under granite or quartz tops with substantial overhangs, in frameless cabinets with added trim, and in any drawer where the last few inches of depth get ignored because they are too hard to reach. The 20 inch slide length suits drawer boxes built to that nominal depth, matching the interior depth of a standard base cabinet with room for the rear hardware.
The G-Slide series uses cold-formed steel members with a zinc finish. Zinc is the working standard for side-mount ball bearing slides in indoor cabinet work: it protects the steel against the humidity and temperature swings of a normal kitchen or shop environment without adding unnecessary cost. The slide sits beside the drawer box and is visible when the drawer is open, so the clean zinc finish keeps the interior looking tidy. This is an indoor product; for exterior or wash-down environments a stainless or coated slide is the right choice.
The GSlide G-Slide 20 inch over-travel slide fits cabinetmakers and contractors who routinely deal with overhangs and cannot use a plain full-extension slide without leaving rear drawer contents out of reach. It also suits renovation projects where new countertops are thicker than the originals and the existing slide length no longer clears. At 90 lb per pair with a hold-in anti-rebound detent, it covers most residential kitchen and utility drawer loads. Cabinet shops running this as their standard over-travel option benefit from the non-handed design, which cuts picking errors and speeds installation. The slide requires 1/2 inch of side clearance per side, so the drawer box is built 1 inch narrower than the cabinet opening.
No. The 1 inch of over-travel affects how far the drawer extends in front of the cabinet, not what happens at the rear. The cabinet member stays fixed; the drawer member travels 1 inch past the point where a standard full-extension slide would stop.
Confirm the sold-as unit on the product listing before ordering. Most G-Slide series slides ship as a pair, but verify the pack quantity shown on the page to be sure you are ordering enough for each drawer.
They are different features. The hold-in anti-rebound detent is a mechanical catch that keeps the drawer closed and stops it from bouncing back open when pushed shut firmly. There is no damper and no spring assist. Soft-close uses a damper to slow the drawer over the last inch of travel. This slide has the detent, not a soft-close damper.
Side-mount slides in face-frame cabinets need rear support because the cabinet side is set back from the face frame. You will need series-compatible rear mounting brackets, sold separately, to support the back end of the slide. The slide itself mounts the same way as in a frameless cabinet once the rear bracket is in place.
The 20 inches is the closed length of the slide, matched to the depth of the drawer box and the cabinet interior. Because this is an over-travel slide, the drawer member extends the full 20 inch slide length and then travels an additional 1 inch, for a total travel that clears a standard 20 inch drawer box completely and then some.
When the countertop is in the way, a standard full-extension slide leaves the back of the drawer unreachable. The GSlide G-Slide 20 inch over-travel slide closes that gap with 1 inch of additional travel, a stay-closed detent, and a non-handed design that keeps the install moving.
Sold In: 10 Set
Quantity | Unit Price | Catalog | ||||
|---|---|---|---|---|---|---|
Sold in: 1 Each |  GY4340RB Mfr# GS4340 RB | GSlide Rear Mounting Bracket, GS4340 RB |
