Pro Value Series 12" 3/4 Extension Self-Close Epoxy Coated Euro Slides PRO 50 Series, Unhanded Side Mount White - 4000-12-1WT

Pro Value Series 12 Inch Epoxy Drawer Slide Use

Pro Value Series 12 inch epoxy drawer slide is a side mount drawer slide that supports drawers in cabinet projects where a 12 inch length is required. The PRO50 epoxy coated 75 lb rated slides are part of Baer Supply's PRO50 line, so they are designed around typical cabinet and furniture drawer loads in woodworking environments. The 3/4 extension design lets the drawer travel out far enough for access while keeping some member engagement, which helps maintain tracking under load. A single captive design keeps the drawer running on the slide path, which supports consistent movement over time. The positive stop feature halts travel at the end of the stroke, helping control drawer extension in daily use. With a white epoxy coated finish, the slide presents a neutral appearance that blends cleanly with light-colored cabinet interiors.

Key Slide Details That Support Daily Use

• PRO50 epoxy coated 75 lb rated slides carry drawers up to the stated weight rating, which suits many residential and light commercial cabinet applications where moderate loads are expected.
• The 3/4 extension travel offers access to stored items while leaving part of the slide engaged, which helps maintain alignment and smooth running under load.
• The self closing action draws the drawer closed at the end of travel, which helps keep drawers shut in normal use without separate closing hardware.
• A single captive design keeps the drawer firmly engaged with the slide track, which supports stable lateral guidance throughout the opening and closing cycle.
• The positive stop function prevents the drawer from overrunning the slide length, which protects against pulling past the designed extension point.
• The white epoxy coated finish on cold rolled steel provides a smooth running surface and neutral color, which suits white or light cabinet interiors.

Mounting, Clearances, And Drawer Member Details

The slide uses side mount installation with a mounting space of 1/2 inch plus or minus 1/32 inch clearance on each side, which defines the required gap between drawer side and cabinet for proper operation. The cabinet member is drilled with 32 mm mounting holes, aligning with the 32 mm system used in many European-style cabinet layouts. On the drawer member, there are both bottom and side mounting holes, allowing positioning along the drawer side or at the drawer bottom edge as needed for the project layout. The slide height is 1-1/2 inch, which helps determine drawer box height and placement relative to cabinet openings when planning stacks of drawers or clearances above runners.

Drawer Slide Role In Cabinet And Furniture Builds

Where This 12 Inch Epoxy Slide Fits Best

This side mount drawer slide is in the Drawer Slides & Accessories category under Slides, Epoxy Coated Euro, so it is suited to cabinet and furniture builds that use epoxy coated Euro slides as the running system. The 12 inch length makes it appropriate for shallow drawers, such as upper kitchen cabinets, vanity drawers, or small shop storage where the cabinet depth matches this length. Being unhanded, the slide can be used on either side of the drawer, which simplifies layout since the same member works on both left and right. The self closing action is built into the lift out disconnect design, so the slide both allows drawer removal by lifting and then assists in drawing the drawer closed when re-engaged in regular use. Because the slide is ANSI/BIFMA tested and approved to Grade 1 requirements, it has been tested to an established performance standard that aligns with typical commercial use expectations.

Why PRO50 Construction Supports Repeatable Results

The slide is constructed from 1.2 mm cold rolled steel with an epoxy coated finish, which provides a rigid steel track and a smooth, coated surface that supports consistent wheel running. The polymer wheel is described as providing quiet, trouble-free performance over the life of the slide, so the wheel material and design are intended to reduce running noise and wear during repeated cycles. Mounting space of 1/2 inch plus or minus 1/32 inch clearance each side gives a clear dimensional target, which helps installers size drawer boxes so the slide runs without binding or excessive play. The 32 mm mounting holes on the cabinet member interface directly with common European cabinet drilling patterns, which supports fast, repeatable alignment in production or shop-built cabinets. Bottom and side mounting holes on the drawer member expand mounting options along the drawer box, which helps accommodate different drawer constructions while maintaining proper engagement with the cabinet member. With a rated capacity of 75 lb and a 3/4 extension travel, the slide balances load handling and reach, aiming to support typical storage loads without overextending the moving members.

Common Questions About This PRO50 Euro Slide

Selecting This 12 Inch PRO50 Slide For Projects

The Pro Value Series 12 inch epoxy drawer slide combines a 75 lb rating, 3/4 extension travel, and self closing action in a side mount euro design that fits face-frame and European applications. With defined 1/2 inch plus or minus 1/32 inch side clearance, 1-1/2 inch height, and 32 mm cabinet member mounting holes, it offers clear installation parameters for cabinet and furniture projects. For projects matching the 12 inch length and these mounting details, this PRO50 epoxy coated slide provides a clearly specified running system ready to integrate into shop workflows.