Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Plastic door track assembly No. 3 is a sliding door hardware solution from EPCO designed for 1/4 inch bypassing wood and/or glass doors, so it gives cabinet and closet openings a simple way to run paired panels in front of each other. The assembly is made for small and/or light doors, which keeps the components appropriately sized for lighter residential or light commercial applications where oversized hardware is not needed. The track and guide are made of high impact, extruded polystyrene, so the system provides a tough plastic running surface that resists typical knocks and everyday use. The 6 foot length suits many standard cabinet, closet, or casework spans in a single piece, which can reduce joints along the run. The white finish lets the track blend into light-colored casework, helping the hardware stay visually unobtrusive in finished installations.
This EPCO sliding door hardware is built for 1/4 inch bypassing wood and/or glass doors, so sizing the door panels to that thickness aligns the doors with the guide and track profile. The assembly uses a plastic upper guide identified as part number 2214, so the door edges engage a plastic guiding surface at the top of the opening. The plastic track identified as part number 214 runs the length of the 6 foot section, so the doors have a matched running channel for smooth travel along the span. Because the system is recommended for small and/or light doors, using it on lighter panels keeps forces on the high impact polystyrene within its intended range. The 6 foot length lets installers position the track in one piece over the opening, which supports straight alignment along the run.
This EPCO plastic door track assembly No. 3 is designed for 1/4 inch bypassing wood and/or glass doors, so it fits projects that use slim panels rather than thick door constructions. In cabinets, wall units, or light closets, the bypassing configuration lets one 1/4 inch door pass in front of the other, so the opening can be adjusted without requiring swing clearance. The high impact, extruded polystyrene material is engineered for small and/or light doors, so it suits lighter panel sizes commonly found in furniture or casework rather than heavy structural doors. Being part of the sliding door hardware category, this assembly works as the guiding component in a broader system, so it plays the role of defining how the doors track during daily operation in tight spaces.
The plastic upper guide #2214 in this assembly holds the upper edge of the 1/4 inch doors in a shaped plastic channel, so the doors stay aligned as they bypass each other during movement. The plastic track #214 runs along the 6 foot length, so the sliding path stays consistent from end to end, supporting predictable travel for both wood and glass doors. High impact, extruded polystyrene construction helps the guide and track absorb contact from small and/or light doors, so the running surfaces remain steady under typical sliding cycles. The 6 foot long white track can span many cabinet or light closet openings in one piece, so the installer can position the track to maintain straight lines that help the doors bypass without binding or wandering off their intended line.
The EPCO plastic door track assembly No. 3 is designed for 1/4 inch bypassing wood and/or glass doors, so it suits slim panels that need to slide in front of each other.
This sliding door hardware is recommended for small and/or light doors, so it works well in cabinet, furniture, and light closet applications using thinner panels.
The EPCO plastic track length is 6 feet, so it can span many standard openings in a single run and provide a continuous guiding surface for bypassing doors.
This EPCO sliding door track and guide are made from high impact, extruded polystyrene, so the components provide a rigid plastic running surface for small and/or light doors.
This plastic track assembly No. 3 uses a plastic upper guide #2214 and a plastic track #214, so the doors engage a matched plastic guiding and running system along the opening.
The white finish lets the track blend into white or light-colored casework, so the sliding door hardware stays visually discreet in finished cabinet or closet installations.
This EPCO plastic door track assembly No. 3 for 1/4 inch bypassing wood and/or glass doors from Wurth Baer Supply provides a 6 foot white track and matching plastic guide for small and/or light panels, so projects gain a defined sliding path. For cabinet, furniture, or light closet openings built around 1/4 inch doors, this high impact, extruded polystyrene sliding door hardware offers a purpose-built guiding system that supports clean motion along the span.
Sold In: 1 Each
