Plastic Door Track Assembly No. 3 for 1/4" Door 6' L, Tan

Plastic Door Track Assembly No. 3 For Bypass Doors

Plastic Door Track Assembly No. 3 is a sliding door hardware solution designed for 1/4 inch by-passing wood and/or glass doors, so it supports common light cabinet or closet door layouts that need doors to slide past each other on parallel tracks. The EPCO assembly uses high impact, extruded polystyrene, providing a plastic track system that resists cracking under normal sliding motion, which helps the doors travel smoothly along the full opening. The 6 foot length gives continuous support across a typical small opening, reducing sagging or misalignment points along the run. The tan color helps the track blend into many light wood or neutral installations, keeping the hardware visually unobtrusive when the doors are open or closed. This assembly is categorized as sliding door hardware, so it fits directly into projects where a compact, guided sliding path is needed for small and/or light doors.

Key Sliding Door Track Details For Installers

• The assembly is for 1/4 inch by-passing wood and/or glass doors, so it addresses applications where two light panels share overlapping travel on a common opening and require coordinated guidance along the same span.
• High impact, extruded polystyrene construction forms the core of the track components, so the plastic body absorbs normal door movement without metal-on-metal noise, helping maintain a predictable glide path over repeated cycles.
• The design is recommended for small and/or light doors, which directs this assembly toward upper cabinets, small closets, or similar openings where modest panel weight benefits from a lighter sliding track approach.
• The assembly is 6 FT long, so it can span many standard smaller openings in one continuous piece, limiting joint transitions that could interrupt door travel or require additional alignment work during installation.
• The tan finish allows the track and guides to sit near the visual tone of many light woods or painted interiors, so the sliding hardware remains less noticeable in finished millwork while still guiding the door panels.

Sliding Door Track Setup And Fit Considerations

This EPCO sliding door hardware is defined as a Plastic Door Track Assembly No. 3 for 1/4 inch doors, so it is intended to interface with panels sized for that thickness as they ride past one another. The 6 FT long track gives a single, uninterrupted guiding surface, which simplifies layout because the installer locates and fastens one continuous line rather than aligning multiple shorter sections. Being recommended for small and/or light doors focuses its use on openings where the panel load matches the capacity of high impact, extruded polystyrene, supporting smooth sliding along the molded track surfaces. The tan high impact plastic construction provides a consistent profile for the door path, which supports repeatable alignment between the plastic components and the door edges during installation and later adjustments.

Using This EPCO Sliding Door Track In Projects

Where This Plastic Door Track Assembly Fits Best

The Plastic Door Track Assembly No. 3 is identified specifically for 1/4 inch by-passing wood and/or glass doors, so it suits projects where two light panels share the same opening and need to slide past each other without swinging. In cabinet or light closet scenarios using small and/or light doors, the high impact, extruded polystyrene material directs the panels along a defined groove, which supports smooth lateral motion as doors cross. As sliding door hardware in the builders hardware category, this assembly integrates into constructions that already rely on overhead or upper guidance to keep panels aligned along the top edge. The 6 FT length helps when the opening width falls within that span, as a single run of track supports the door edges from one side to the other, helping maintain consistent clearance between by-passing panels as they move.

Details That Support Repeatable Sliding Performance

The EPCO assembly description specifies high impact, extruded polystyrene, which forms a resilient sliding surface so door edges track inside durable plastic channels rather than against bare wood, promoting repeatable movement over time. The Web Description notes Plastic Upper Guide #2214 and Plastic Track #214, so the guide and track elements are matched components that work together to establish a defined upper path for the doors as they by-pass. Because this assembly is recommended for small and/or light doors, the plastic guide and track focus on managing lighter panel loads, which aligns the material strength with typical cabinet or modest closet door applications. The 6 FT Long dimension means both the Plastic Upper Guide #2214 and Plastic Track #214 extend over a substantial continuous distance, which supports uniform tracking and alignment from one end of the opening to the other.

Common Questions About This EPCO Door Track

Select This Track For 1/4 Inch Bypass Doors

The EPCO Plastic Door Track Assembly No. 3 for 1/4 inch by-passing wood and/or glass doors provides a 6 FT Long, tan, high impact, extruded polystyrene track path that serves small and/or light doors. The presence of Plastic Upper Guide #2214 and Plastic Track #214 gives a defined sliding route tailored to 1/4 inch panels. For projects needing sliding door hardware in this size range, this assembly offers a coordinated guide and track setup that supports smooth, consistent bypass movement across the opening.