Plastic Door Track Assembly No. 3 for 1/4" Door 6' L, Gray

Plastic Door Track Assembly No. 3 For 1/4 Inch Doors

Plastic door track assembly No. 3 defines this EPCO sliding door hardware as a matched track and guide setup for 1/4 inch by-passing doors, so installers get a single, coordinated solution instead of piecing parts together. The product is specified for 1/4 inch by-passing wood and/or glass doors, which sets clear door thickness and material expectations for planning a run of small or light panels. As part of EPCO sliding door hardware, this assembly fits directly into builders hardware workflows where consistent door movement is essential. The track is 6 ft long, giving enough continuous run for typical small or light sliding door openings without splicing shorter pieces. Its gray color helps it visually blend with many cabinet or closet interiors, which keeps the focus on the doors while still matching common hardware tones. Overall, the assembly is set up to serve small and/or light sliding door projects where a compact, 1/4 inch system is needed.

Key Track Assembly Details For Sliding Performance

• The EPCO brand identifies the plastic door track assembly No. 3 with manufacturer part 3-G-6, which helps installers match this exact track and guide set on repeat jobs or when expanding an existing run.
• The assembly is designed for 1/4 inch by-passing wood and/or glass doors, so door panels slide past one another on separate lines, allowing two panels to share a relatively tight opening without needing hinged clearance.
• The door track assembly is recommended for small and/or light doors, focusing its use on lighter panels where a high impact plastic track can guide movement without the weight demands of heavy commercial units.
• The track is 6 ft long, which lets installers cover many residential or light commercial openings with a single continuous length, reducing joints that can cause hang-ups at panel transitions.
• The door track assembly is gray, so the hardware presents a neutral tone that works with a wide range of cabinet interiors and trim colors, helping the track visually recede behind wood or glass doors.
• The material is described as high impact, extruded polystyrene, giving the track and related plastic elements impact resistance that supports repeated sliding use in everyday door operation.

Sliding Door Track Assembly Installation Context

The plastic door track assembly No. 3 is specified for 1/4 inch by-passing doors, which means door panel grooves or edge hardware can be sized precisely to that thickness for a proper running fit. Because the track is high impact, extruded polystyrene, installers can work with a plastic profile that resists common knocks and edge contact during hanging and adjustment. The 6 ft length lets the track span most small and/or light sliding openings in one piece, simplifying layout because there is a single continuous line to align with the cabinet or opening edges. Since the assembly is intended for small and/or light doors in wood and/or glass, it fits well into built-ins, closets, or casework where low to moderate panel loads are expected over time.

Where This EPCO Track Assembly Fits Best

Using No. 3 Assembly On 1/4 Inch Doors

The EPCO plastic door track assembly No. 3 is described specifically for 1/4 inch by-passing wood and/or glass doors, so it targets projects where panel thickness is already defined at a quarter inch. That fit lets fabricators cut grooves or set edge hardware specifically around the track interface, while knowing the sliding hardware is tuned to that dimension. Because it is recommended for small and/or light doors, this assembly finds its best use on compact openings such as smaller closets, casework, or cabinets where panels do not carry heavy loads. In these applications, the by-passing layout allows one 1/4 inch door to slide in front of the other, using two tracks instead of swinging outward on hinges, which is helpful where swing clearance is tight. The gray finish keeps the hardware visually understated behind wood grain or glass panels, supporting clean lines when doors are open or closed.

High Impact Polystyrene Track For Consistent Travel

The track and guide components are described as high impact, extruded polystyrene, which gives the sliding path a plastic profile built for impact resistance along the running surface. In day-to-day use, that high impact characteristic supports consistent travel as doors move against the track, because the material is designed to tolerate the knocks and bumps typical of repeated operation. The assembly is stated to include the Plastic Upper Guide 2214 and Plastic Track 214, so the sliding path and top guidance are matched components from the same EPCO system. Having both guide and track from a single No. 3 assembly simplifies aligning the upper control with the running surface, which helps doors stay in their intended by-passing paths over the full 6 ft length. The defined 6 ft span means both the Plastic Track 214 and its related guidance can be laid out as one continuous run, reducing opportunities for misalignment at joints.

Practical Questions About This Sliding Door Assembly

Choose This EPCO Track For 1/4 Inch By-Passing Runs

The EPCO plastic door track assembly No. 3 for 1/4 inch by-passing wood and/or glass doors combines a high impact, extruded polystyrene track with matched guide components in a 6 ft gray length, aligning well with small and/or light sliding door openings. Selecting this 3-G-6 assembly sets the door system around a defined quarter-inch panel standard and a continuous 6 ft track, supporting straightforward layout for compact sliding runs.