Plastic Door Track Assembly No. 3 for 1/4" Door 5' L, Gray

Plastic Door Track Assembly No. 3 For 1/4 Inch Doors

Plastic door track assembly No. 3 is a sliding door hardware solution from EPCO designed for 1/4 inch by-passing wood and/or glass doors, so it supports typical light cabinet or closet applications using slim panels. The assembly is made from high impact, extruded polystyrene, which provides a rigid guiding surface that resists damage under normal sliding door use. This material construction also helps the track maintain its profile, so doors move consistently along the opening. The track assembly is classified as sliding door hardware, so it integrates into layouts where doors need to slide past each other rather than swing. The gray color finish identifies the track visually against surrounding materials, which helps during layout, cutting, and alignment on site. A 5 foot length gives a continuous run for many small or light door openings, reducing joint lines along the travel path.

Key EPCO Sliding Track Details For Daily Use

• The design for 1/4 inch by-passing wood and/or glass doors establishes a defined panel thickness range, so installers can match door material to the track for smoother sliding action on small and/or light doors.
• High impact, extruded polystyrene construction creates a single-piece plastic body that absorbs everyday contact from door edges, which supports consistent door guidance over repeated open-and-close cycles.
• The 5 foot long track section provides an extended sliding surface in one piece, which helps maintain straight door travel on installations that fall within that span.
• The gray color of the Plastic Door Track Assembly No. 3 provides a neutral appearance against many cabinet or wall finishes, which helps the hardware visually recede in finished installations.
• The assembly is categorized as sliding door hardware under builders hardware, aligning it with other components used in by-passing door systems where controlled linear movement is required.

Sliding Door Track Layout And Fit Considerations

The Plastic Door Track Assembly No. 3 is specified for 1/4 inch by-passing wood and/or glass doors, so layout work revolves around creating parallel tracks that allow two doors to pass each other on separate lines. The 5 foot length gives planners a fixed maximum opening span for each run, simplifying cut calculations when sizing the track to cabinet or wall dimensions. Because the assembly is produced from high impact, extruded polystyrene, cuts at the ends remain clean and stable, which supports accurate fit between jambs or cabinet sides. As sliding door hardware, this assembly defines a clear path for the panels, so hinge clearances are irrelevant and the focus remains on track alignment and door overlap. The gray finish also makes scribe marks and alignment references easier to see against the track during installation.

Using This By-Passing Door Track In Projects

Where This Plastic Door Track Assembly No. 3 Fits

This Plastic door track assembly No. 3 for 1/4 inch door 5 foot L, gray is designed for by-passing wood and/or glass doors, so it fits applications where two small or light doors slide past each other in a shared opening. In cabinet or light partition scenarios, the 5 foot long configuration supports openings that stay within that span, which aligns well with many residential or light commercial casework runs. Because the product is part of the sliding door hardware class in builders hardware, it serves in systems where linear, guided motion is required rather than hinged movement. The sizing for 1/4 inch door material means it suits slim panel constructions, so designers can work with thinner wood or glass while staying within the track's design envelope. The gray tone also coordinates with neutral interiors, so the hardware presence remains understated in finished work.

Why These Track Details Support Repeatable Sliding Results

The high impact, extruded polystyrene body of the Plastic Door Track Assembly No. 3 provides a tough, uniform channel for the door edges, which promotes repeatable sliding performance over time as doors follow the same molded profile. Being recommended for small and/or light doors, the track focuses on panel weights that this plastic construction supports effectively, so installations remain in a working range that favors smoother motion. The defined use for 1/4 inch by-passing wood and/or glass doors establishes a clear interface dimension, giving fabricators a target thickness so door edges sit correctly within the track. A 5 foot length in a single piece reduces transitions along the sliding path, which helps minimize points where doors could catch during travel. The gray color visually contrasts against many door materials, supporting straightforward visual checks of alignment while positioning the track and doors.

Common Questions About This Sliding Door Track Assembly

Selecting This Track For 1/4 Inch Sliding Doors

The Plastic door track assembly No. 3 for 1/4 inch door 5 foot L, gray delivers a defined sliding solution for small and/or light by-passing wood and/or glass doors, so it fits projects built around slim, overlapping panels. High impact, extruded polystyrene construction provides a stable channel profile for door travel, supporting consistent motion along the opening. Its 5 foot length suits many cabinet and light opening dimensions, giving a practical span for layout. For projects requiring sliding door hardware that matches 1/4 inch by-passing door construction, this EPCO assembly provides a focused option ready for integration into builders hardware plans.