Sugatsune Overlay Pocket Door Kit, Min. Cab. Depth 16-9/16", Door Height 35-7/16" - 47-1/4", 4-Slides, Further Door Retraction, - ALT-ST15-D10L-16

Sugatsune Overlay Pocket Door Kit For Cabinets

Sugatsune overlay pocket door kit is a pocket door hardware system designed for cabinets where the door overlays the face. The system is classified as pocket door hardware, so it focuses on smooth door movement and consistent overlay positioning for cabinet projects. The kit is manufactured by Sugatsune America, giving installers a defined product source when matching specifications or coordinating with existing Sugatsune hardware in a project. The system is listed as an overlay pocket door system, so the door travels into the cabinet while starting from an overlay position on the front. An overlay amount up to 3/8 inch, or 10 mm, allows the door edge to sit over the cabinet opening within that range, helping align with surrounding fronts in a run. This overlay pocket door system is sold per kit, which fits project planning where hardware is installed per cabinet opening.

Overlay Pocket Door System Details For Projects

• The overlay pocket door system provides door alignment adjustability, which lets installers fine-tune the overlay position relative to the cabinet face so reveals line up across adjacent fronts.
• An overlay amount up to 3/8 inch, or 10 mm, defines how far the door can overlap the cabinet opening, helping match face-frame or frameless layouts that are designed around a specific overlay dimension.
• The system uses four slides, which distribute the door movement across multiple runners so the travel into and out of the cabinet remains controlled on taller doors.
• A synchronized board is part of the system, which coordinates slide motion so both sides of the door move together and reduce racking as the door is opened or retracted.
• The overlay pocket door system is part of the ST15 L-type 16 designation, which identifies it within the Sugatsune pocket door family for projects that follow manufacturer part references.

Installation Adjustments And Overlay Fit Setup

The overlay pocket door system provides door alignment adjustability, so after mounting, the door position can be adjusted relative to the cabinet face to dial in even gaps. The overlay damper unit uses an adjustment screw, which gives a defined adjustment point for controlling how the damper engages during closing or opening cycles. An overlay amount up to 3/8 inch, or 10 mm, sets a clear design envelope for how much the door overlays the opening, which helps during cabinet layout and hinge positioning. The minimum cabinet depth of 16-9/16 inches establishes how deep the cabinet must be so the door can fully retract into the pocket, which directly affects case construction dimensions. The door height range from 35-7/16 inches to 47-1/4 inches identifies the door sizes supported by the system, so doors in that range can travel and retract as intended.

How This Pocket Door Hardware Works In Use

Overlay Pocket Door System In Cabinet Applications

This overlay pocket door system is intended for cabinet applications that need a door to open and then slide back into the case. The product is categorized as pocket door hardware under multimedia and workspace components, so it suits cabinets that conceal equipment or workspace areas behind doors. The minimum cabinet depth of 16-9/16 inches gives builders a concrete depth requirement when designing the cabinet box so the door can move fully into the pocket. A supported door height range from 35-7/16 inches to 47-1/4 inches targets medium-height cabinet doors, allowing the system to serve tall base cabinets or lower sections of storage walls. The overlay amount up to 3/8 inch, or 10 mm, keeps the door starting position proud of the opening by a defined amount, which is useful when aligning with other overlay doors on the same run of cabinetry.

Details That Support Smooth Retraction And Alignment

The fittings in this overlay pocket door system allow the door to retract further into the cabinet than the ALTST20-D10 series, which means the open door can sit deeper inside the case and away from the face line of adjacent fronts. This further door retraction helps keep the door clear of nearby hardware or openings when the workspace or equipment behind the door is in use. Four slides guide the motion, distributing support across multiple points so the door tracks in and out with reduced side play. A synchronized board coordinates movement between slides on the system, which helps keep the door square as it transitions from swinging to sliding motion. Door alignment adjustability lets installers correct for minor cabinet or door variances, resulting in straighter reveals and a more consistent overlay look. The overlay damper unit with adjustment screw provides controlled damping at the end of travel, which can soften movement and contribute to more predictable door behavior over repeated cycles.

Installer Questions About This Pocket Door System

Select This Overlay Pocket Kit For Defined Fit

This Sugatsune America overlay pocket door kit, part number ALT-ST15-D10L-16, provides a defined combination of minimum cabinet depth, door height range, and overlay amount for cabinet projects. The door alignment adjustability and overlay damper unit with adjustment screw support precise setup so reveals and motion can match the design intent. Four slides, a synchronized board, and fittings that allow further door retraction than the ALTST20-D10 series work together to manage door movement into the cabinet. For cabinet layouts built around an overlay pocket door system with these parameters, this kit offers a matched hardware solution that aligns with those requirements.