Domi 2-Cam Adjustable Wing Mounting Plate, Nickel-Plated, Screw-On, 6mm, Salice BARGL69F/16

Domi Mounting Plate For Salice Hinge Systems

Domi 2-cam adjustable wing mounting plate gives cabinet builders a 6mm screw-on base plate specifically designed for Salice hinges, so you can set up consistent hinge mounting points across a full run of doors. This Salice America hinge mounting plate is part of the Salice Domi system, tying directly into the manufacturers hinge geometry for dependable alignment. Nickel-plated steel construction resists corrosion in typical cabinet environments, which supports long-term, repeatable hinge performance. Classified under hinge mounting plates, this plate works as the structural bridge between the cabinet side and the hinge arm, so hinge loads transfer cleanly into the casework. As a wing style mounting plate, it spreads bearing over a wider surface area on the cabinet side, which supports stability on tall or heavy doors where hinge movement is frequent. The defined 6mm plate height also establishes a predictable reference line for layout.

Key Mounting Plate Details For Daily Use

• The 6mm mounting plate height sets a fixed reference between cabinet side and hinge arm, which simplifies line boring layouts and helps installers repeat consistent reveals across multiple doors.
• Stamped or die-cast steel construction with nickel plating provides a rigid mounting platform with corrosion resistance, which supports long-term hinge function in typical kitchen and bath cabinet conditions.
• Two cam adjustment built into the plate provides cam height adjustment of plus or minus 2 mm, allowing controlled vertical fine-tuning after installation to straighten door alignment without redrilling.
• The same two cam system also delivers cam depth adjustment from -0.5 mm to +2.8 mm, letting you bring doors closer or farther from the cabinet to dial in overlay and close gaps along the case.
• Cabinet side fastening with pre-mounted Euro screws ties directly into standard 5 mm system holes, which speeds installation on line-bored cabinets and supports accurate positioning in production work.
• Compatibility with series 100, 200, 400, F, M, universal, and Silentia hinges allows one plate style to serve multiple Salice hinge families, which simplifies hinge planning across mixed door applications.

Installation And Adjustment On Cabinet Sides

This 6mm screw-on hinge mounting plate fastens to the cabinet side using pre-mounted Euro screws, so it aligns naturally with standard system holes in frameless casework. Once the plate is fixed, the two cam adjustment design provides cam height adjustment of plus or minus 2 mm, which lets you move the hinge connection up or down to correct door sag or reveal changes after the case is assembled. The same mechanism provides cam depth adjustment from -0.5 mm to +2.8 mm, so you can shift the door in or out relative to the cabinet front without moving the plate. Because this plate is designed for Salice hinge series 100, 200, 400, F, M, universal, and Silentia, it works as a common interface that keeps mounting geometry consistent when mixing different Salice hinge models on a project.

Using This Hinge Plate In Cabinet Projects

Where This Salice Hinge Mounting Plate Fits

This Salice hinge mounting plate is designed for use with series 100, 200, 400, F, M, universal, and Silentia hinges, so it can serve across a range of Salice hinge styles on frameless cabinets. The 6mm plate height creates a defined offset between the cabinet side and hinge arm, which helps maintain consistent overlay and reveal targets across doors using different Salice hinge series. As a wing style plate, it spreads contact on the cabinet side panel, which is valuable on tall pantry doors, wardrobe cabinets, or wide doors where hinge forces are higher. Cabinet side fastening through pre-mounted Euro screws connects directly into system 32 line boring, supporting both shop production and field work on frameless furniture-style cabinets. Because this plate functions as a hinge base plate within the Salice system, it anchors the hinge in a way that maintains the manufacturers intended opening geometry.

Adjustment Details That Support Clean Results

The two cam adjustment built into this hinge mounting plate directly affects day-to-day alignment results. Cam height adjustment of plus or minus 2 mm gives installers a vertical correction range on each hinge, which helps bring multiple doors into a straight, even sightline without reworking boring patterns. The cam depth range from -0.5 mm to +2.8 mm establishes controlled in-and-out movement at the plate level, so fine overlay changes happen through the hardware rather than through cabinet modification. Nickel-plated stamped or die-cast steel construction means the adjustment cams work against a rigid, corrosion-resistant body, helping the settings hold position under repeated door use. By working with Salice hinge series 100, 200, 400, F, M, universal, and Silentia, this plate lets a shop standardize on one adjustment style while still selecting hinge arms for specific door applications. The lifetime warranty supports long-term service expectations around this hinge mounting plate choice.

Common Questions About This Salice Mounting Plate

Select This Plate For Adjustable Salice Hinge Runs

The Domi 2-cam adjustable wing mounting plate gives shops and installers a 6mm Salice hinge mounting plate with defined cam height and depth adjustment ranges for precise door alignment. Nickel-plated steel construction, pre-mounted Euro screw fastening, and broad compatibility with Salice series 100, 200, 400, F, M, universal, and Silentia hinges make it practical when standardizing hinge hardware. When ordering from Wurth Baer Supply, use manufacturer part BARGL69F/16 to match this specific hinge mounting plate on repeat cabinet jobs.