Domi Cam Adjustable Wing Mounting Plate Use
Domi cam adjustable wing mounting plate describes a hinge mounting plate from Salice America that ties directly into the Salice hinge system, so cabinet hinges seat securely on a consistent 12mm mounting base. As a hinge mounting plate in the hinges and hinge base plates category, it carries the load of the hinge arm on the cabinet side, which keeps the door connection stable over time. The die-cast or stamped steel construction forms a solid platform under the hinge, while the nickel plating resists corrosion in typical cabinet environments. Being part of the hinge mounting plates product class, it is designed as the interface between cabinet side and Salice hinge arm, which simplifies planning for new builds or service work on existing installations. The Salice America brand alignment gives installers one family of hinge and plate components for series 100, 200, 400, F, M, universal, and Silentia+ hinges.
Key Details That Support Cabinet Hinge Work
- The 12mm mounting plate height establishes a predictable door overlay geometry, so layouts using Salice hinges can be repeated across multiple cabinets with the same reveal and alignment.
- Two cam adjustment on the plate provides cam height adjustment of plus or minus 2 mm, letting installers fine-tune door position vertically without redrilling the cabinet.
- The second cam offers depth adjustment from -0.5 mm to +2.8 mm, so the door-to-cabinet gap can be dialed in after mounting, helping correct minor drilling or boring variances.
- Construction from stamped steel or die-cast steel creates a rigid base under the hinge arm, which supports long-term hinge performance under normal cabinet door loading.
- Nickel plating over the steel plate resists corrosion, helping the hinge connection retain smooth function in typical kitchen, bath, or casework environments.
- The hinge mounting plate design integrates with Salice hinge arms, simplifying hardware selection when standardizing on Salice America hinge series in a shop or on a job.
Mounting Plate Installation And Euro Screw Fixing
This hinge mounting plate uses a cabinet side fastening method based on pre-mounted Euro screws, so the plate locates directly into Euro system holes without extra layout steps. With Euro screws already integrated at the cabinet-side connection, the installer drives the plate into prepared system holes, which speeds installation when working through a run of cabinets. The Domi cam adjustable wing configuration provides access to both height and depth adjustment cams after the hinge arm is attached, so fine-tuning can be handled from the cabinet interior. Because the plate is designed as a screw-on solution for the Euro system, it aligns naturally with frameless cabinet construction and 32 mm line boring patterns.
How This Salice Mounting Plate Works In Practice
Where This 12mm Hinge Mounting Plate Fits
This Salice America hinge mounting plate is specified for use with series 100, 200, 400, F, M, universal, and Silentia+ hinges, so one plate style can serve a wide range of Salice hinge bodies on a project. The 12mm plate height sets the basic starting point for overlay and gap on frameless cabinets using these hinge families, supporting consistent reveals across banks of doors. As a Domi cam adjustable wing plate, it is built to sit on the cabinet side and connect to the hinge arm, so it becomes the structural link between cabinet carcass and moving door. Because it is a hinge base plate in the Salice system, it lets a shop standardize boring patterns and hinge choices, then rely on the plate height to hold the design line on every cabinet run. The Euro screw fastening method pairs naturally with system holes in panel-based cabinetry, so plate positioning follows established drilling references on production equipment.
Adjustment And Alignment Benefits During Setup
The two cam adjustable design gives this plate cam height adjustment of plus or minus 2 mm, so a door that sits slightly high or low can be brought into line without reworking the boring pattern. The same plate also provides cam depth adjustment from -0.5 mm to +2.8 mm, letting the installer move the door closer to or farther from the cabinet front to achieve the desired gap. Because these adjustments are built into the hinge mounting plate rather than relying solely on the hinge arm, the cabinet-side interface can correct small casing or drilling tolerances while keeping the hinge screws tight. Nickel-plated stamped or die-cast steel construction means the cam mechanisms work within a rigid platform, so door position set during installation remains stable under typical cabinet use. With this combination of height and depth adjustment, a single BARGRC9/16 mounting plate can handle fine alignment on multiple doors in a run while maintaining the Salice system geometry.
Common Questions About This Salice Mounting Plate
What type of hinge system does this plate support?
This hinge mounting plate works with Salice series 100, 200, 400, F, M, universal, and Silentia+ hinges, so one plate style can be used across many Salice hinge bodies in a project.
How does the two cam adjustable hinge plate help alignment?
The two cam adjustable hinge plate offers plus or minus 2 mm height and -0.5 mm to +2.8 mm depth adjustment, allowing precise door alignment without altering cabinet drilling.
What is the function of the 12mm hinge mounting plate height?
The 12mm hinge mounting plate height sets a consistent reference for door overlay and gap, helping maintain uniform reveals across multiple cabinets using the same Salice system.
How is this Euro screw hinge mounting plate fastened?
This Euro screw hinge mounting plate uses pre-mounted Euro screws on the cabinet side, so it fastens directly into system holes in frameless panels for repeatable positioning.
Why does nickel-plated steel matter for this mounting plate?
The nickel-plated stamped or die-cast steel construction resists corrosion and provides a rigid base, helping the hinge connection stay stable in normal cabinet environments.
What does the BARGRC9/16 part number identify?
The BARGRC9/16 part number identifies this specific Salice Domi cam adjustable wing mounting plate, helping match it with the correct Salice hinges and cabinet drilling layout.
Selecting This Plate For Salice Hinge Projects
Choosing this Salice America Domi cam adjustable wing mounting plate aligns cabinet work with a 12mm, two cam adjustable hinge base that ties directly to series 100, 200, 400, F, M, universal, and Silentia+ hinges. The pre-mounted Euro screw fastening method speeds repeat cabinet-side installation, while the nickel-plated stamped or die-cast steel body provides a stable interface for ongoing hinge performance. For jobs built around the Salice system, this BARGRC9/16 mounting plate supports consistent overlay, clean reveals, and straightforward cam-based adjustment across an entire run.
