Genesis Durawrap 96" Drawer Side 5-1/2", White, BSC140W

Genesis Drawer Side Blanks For Consistent Drawers

Genesis drawer side blanks use vinyl Durawrap drawer side material so each run of drawers matches in color and surface from shop to install. The 1/2 inch thick construction creates a solid sidewall that supports stable drawer assemblies over time. Each blank measures 5-1/2 inches high by 96 inches long, giving enough length to cut multiple sides from one piece for efficient layout. The Durawrap material is 8 mil thick and non-flammable, which helps maintain a durable, uniform surface in typical cabinet environments. A high density particle board core sits under the Durawrap, providing greater screw holding strength where slides and fronts fasten into the drawer side. The blanks are white, which works well with many cabinet interiors and keeps drawer boxes looking clean and consistent across a project.

Key Drawer Side Details That Support Workflow

• Vinyl Durawrap material is 8 mil thick and non-flammable, giving the drawer side a tough, uniform skin that stands up to normal shop handling and cabinet use.
• The core made of high density particle board delivers greater screw holding strength, which supports secure attachment points for drawer slides, fronts, and back pieces.
• All wood blanks are pre-finished with Endura ultraviolet cured top coat, so the surfaces arrive ready to assemble without separate finishing steps in the shop.
• Each drawer blank has a 1/4 inch drawer bottom dado, saving a machining pass while setting a repeatable groove location for fitting drawer bottoms.
• A 9/16 inch, or 14 mm, bottom reveal is built into the blank design, giving predictable clearance from the bottom edge to the drawer bottom for consistent fit and appearance.
• Blank lengths are 8 feet, allowing multiple drawer sides to be cut from each piece to streamline cutting patterns on longer cabinet runs.

Drawer Side Fit, Heights, And Cut Length Planning

These Genesis drawer side blanks are classified as drawer side materials that are 1/2 inch thick, so planning joinery, fastener length, and slide placement follows that consistent side thickness. Drawer side heights for this line range from 2-3/4 inches through 10 inches, letting a shop match side height to shallow, standard, or deeper storage drawers within the same system. Each blank length is 96 inches, which helps lay out parts to reduce waste when cutting paired sides for several drawers. A square edge profile on the blanks gives a straightforward reference for sizing, squaring, and applying any additional edge work needed for a particular build.

Using Vinyl Durawrap Drawer Sides In Cabinet Runs

Where These 5-1/2 x 96 Drawer Sides Apply

The 5-1/2 inch x 96 inch white drawer side format suits drawer construction systems that rely on consistent blanks for multiple cabinet boxes. The 1/4 inch drawer bottom dado already machined into every blank supports straightforward assembly in drawer construction systems that use a captive bottom. A 9/16 inch bottom reveal built into the design sets a known distance between the drawer bottom and lower edge of the side, which simplifies planning clearances against cabinet hardware or face frames. Drawer side heights across the product line from 2-3/4 inches through 10 inches allow the same Durawrap and core construction to be used for different drawer depths in kitchens, baths, or casework where uniform interior appearance is desired. The white finish from the vinyl Durawrap and Endura ultraviolet cured top coat helps these sides blend into light-colored cabinet interiors and keeps drawer interiors bright.

Details That Support Repeatable Drawer Box Results

The vinyl Durawrap material at 8 mil thickness provides a consistent, stable surface for fastening and handling, so the screw holding strength of the high density particle board core can be used effectively where slides or drawer fronts attach. The non-flammable nature of the Durawrap material supports use in typical commercial and residential woodworking environments that expect basic fire-resistance characteristics in finished components. Because all wood blanks are pre-finished with the Endura ultraviolet cured top coat, the assembly process focuses on cutting and joinery rather than separate finishing stages, which supports more predictable lead times. A square edge profile gives an accurate reference surface when setting against fences or tables, which helps keep parts square as they are cut to final drawer side length. Blank lengths of 8 feet keep cutting patterns simple along standard shop equipment, aiding repeatable part sizing across multiple identical drawers.

Common Questions About Genesis Drawer Side Blanks

Select Genesis Drawer Sides For Consistent Builds

The Genesis drawer side materials at 1/2 inch thick with vinyl Durawrap and a high density particle board core give a defined structure for repeatable drawer projects. The 5-1/2 inch x 96 inch white format, pre-finished with Endura ultraviolet cured top coat, supports efficient cutting and assembly inside a consistent drawer construction system. With the 1/4 inch drawer bottom dado, 9/16 inch bottom reveal, and square edge profile already established, each blank provides predictable references for fitting bottoms and aligning joinery. For shops building multiple drawers in coordinated heights from 2-3/4 inches through 10 inches, these Genesis drawer side blanks allow a single material family to support varied drawer depths while keeping interior appearance and construction details aligned.