Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Pro Value Classic Series 3 inch pull is a satin nickel cabinet handle designed for everyday cabinet and drawer use. The 3 inch, or 76 mm, center to center mounting spreads the load across two fasteners, which helps the pull feel solid when opening heavier doors or drawers. The zinc die cast material forms a rigid body, so the handle keeps its shape under repeated pulling in busy kitchens, shops, or work areas. The satin nickel finish diffuses light, which helps fingerprints and small scuffs stand out less during daily use. A full length of 4-5/16 inch gives fingers more space between mounting points, which is useful on thicker drawer fronts. A 3/4 inch projection sets the grip away from the surface enough for a clear handhold while staying close for a clean, compact profile on the face of the cabinet.
This Pro Value Series cabinet pull uses a 3 inch center to center measurement between mounting points, which sets a clear standard for drilling or boring on doors and drawers. The length of 4-5/16 inch means the handle extends beyond the screw locations, which gives the pull a defined grip area even on wider stiles or rails. With a 3/4 inch projection, the pull stands off the face just enough for comfortable finger clearance, which is helpful on thicker door edges. The 3/4 inch width presents a consistent contact surface, which supports a firm grip from different angles, whether mounted vertically on doors or horizontally on drawers.
The 3 inch center to center spacing on this Classic Series pull aligns with a common cabinet drilling pattern, which suits both new cabinet layouts and handle changes on many existing fronts drilled at that distance. The satin nickel finish gives the pull a neutral metallic appearance, which works alongside a wide range of painted or stained doors without dominating the cabinet face. With a full 4-5/16 inch length, the pull covers a modest span across drawer fronts, which can visually tie multiple cabinets together when used repeatedly along a run. The 3/4 inch projection keeps the handle close to the surface, which is useful on walk-through areas where cabinets sit near traffic paths and a low-profile grip helps limit contact.
The 3 inch center to center dimension on this SZCL4-SN satin nickel pull provides a fixed reference between mounting holes, which supports consistent drilling jigs and repeatable alignment from cabinet to cabinet. The zinc die cast construction produces uniform parts from piece to piece, which helps pulls line up evenly along doors and drawers of the same size. A 3/4 inch width defines the visible band of metal on each installation, which keeps the hardware line consistent even as cabinet dimensions vary across a project. The 3/4 inch projection defines how far the grip stands off the face, which lets installers anticipate clearance around adjacent doors or nearby edges when laying out an entire bank of cabinets.
This cabinet pull is specified with an 8-32 screw size, which points to a standard machine screw interface and guides drill bit selection for mounting the hardware into cabinet fronts.
The pull length is 4-5/16 inch, which extends past the mounting holes to create a defined gripping span that looks proportionate on typical cabinet doors and drawers.
This pull has a 3/4 inch projection, which sets the handle slightly off the cabinet surface so fingers can engage the grip without crowding the door or drawer face.
The SZCL4-SN pull is zinc die cast, which creates a rigid one-piece body that stands up to repeated opening and closing on cabinet doors and drawers.
This pull uses a satin nickel finish, which provides a muted metallic look that pairs with many hinge and fixture finishes in kitchens, baths, and work areas.
The pull has a 3 inch center to center dimension, which matches a common drilling pattern and supports consistent alignment across multiple cabinet doors and drawers.
The Pro Value Classic Series 3 inch pull ties together projects that rely on a standard 3 inch center to center layout, which keeps drilling patterns consistent from box to box. With zinc die cast construction and a satin nickel finish, the SZCL4-SN pull delivers a steady grip and a neutral metallic look that works across kitchens, baths, and shop cabinets. Using the defined 4-5/16 inch length, 3/4 inch width, and 3/4 inch projection, installers can plan handle lines that stay visually uniform while still providing practical clearance for everyday cabinet use.
Sold In: 1 Each
