Deltana solid brass cabinet hinges come in an array of fine finishes with ball tip finials as standard, giving installers a consistent decorative hinge point that supports clean cabinet lines on finished work. As a semi-concealed hinge in the full mortise category, this hinge tucks most of its body into the door and frame, which helps maintain a streamlined cabinet face while still allowing the leaf to carry the load at the joint. The 2-1/2 inch by 2 inch size defines the hinge footprint on the stile and door edge, so layout remains predictable across multiple door runs. Brushed chrome finish provides a neutral, project-friendly appearance that ties in with other brushed cabinet hardware finishes on contemporary or commercial jobs. The free swinging design keeps door motion smooth through the opening arc, which supports accurate overlay alignment when doors are hung in a series.
The 2-1/2 inch by 2 inch hinge size establishes both the leaf height and width, so hinge placement can be planned around cabinet rail intersections and door panel proportions. With a thickness of 0.093 inch, the hinge leaf depth defines the mortise cut, which helps installers match the pocket depth to keep the door surface flush with the face frame when the hinge is closed. Square corner leaves align with mortises cut using straight bits or chisels, allowing crisp shoulder lines around the hinge perimeter. The hinge is drilled for wood screws sized #7 by 3/4 inch, giving a fastener length that engages typical cabinet frame stock while remaining within the leaf hole pattern. As a semi-concealed full mortise hinge, only the knuckle and finials present at the gap, which preserves a clean visual line on the cabinet face while still providing a robust pivot point.
This hinge sits in the semi-concealed face-frame hinge class, so it is suited to cabinets where most of the hardware is buried within the frame and door while the barrel remains visible at the gap. The full mortise mounting type places one leaf in the door edge and the other in the frame, creating a defined pivot line that works well on cabinet doors that require precise reveals around the opening. Because the hinge measures 2-1/2 inches by 2 inches, it lines up well on small to medium cabinet doors where a compact but substantial hinge footprint is appropriate. The 0.093 inch thickness gives a mortise dimension that balances strength and cut depth, supporting a stable door edge while still preserving material in the stile. Brushed chrome finish ties visually into brushed pulls and knobs, so the exposed knuckle and ball tip finials sit comfortably alongside other visible hardware on the cabinet face.
As a solid brass cabinet hinge, this unit provides a consistent machined body that holds its geometry at the mortise, helping multiple doors share the same swing path when hinges are set from the same layout marks. The six-hole pattern across the leaves allows screws to anchor near both ends and the center of the hinge, which spreads forces from door movement into the surrounding wood and supports long-term hinge seating. Square corner leaves eliminate the need to round mortise corners, so routed or chiseled pockets can follow straight layout lines and speed up hinge preparation on repeat installations. The ball tip finials at the knuckle ends give a defined termination point at the barrel, which keeps the visible portion of the hinge looking finished even when doors are slightly open. As a free swinging hinge, motion through the arc remains smooth from closed to open, which supports accurate door positioning against stops or bumpers and helps doors land consistently along the face frame.
The CH2520U26D is a Deltana solid brass cabinet hinge in the semi-concealed full mortise hinge class, so it mounts into mortises while leaving the barrel visible at the gap.
The hinge measures 2-1/2 inches by 2 inches, which sets the footprint on the door and frame and guides mortise layout around rails and stiles.
The 0.093 inch hinge thickness defines how deep the mortise must be cut so the door face aligns properly with the frame when the hinge is closed.
The square corners match mortises cut with straight bits or chisels, which keeps hinge pockets crisp and speeds layout on cabinet doors and frames.
This hinge is drilled for #7 by 3/4 inch wood screws, giving a fastener length suited to typical cabinet stock while matching the factory hole pattern.
The ball tip finials finish the ends of the hinge barrel, providing a decorative detail that matches the brushed chrome hinge body on exposed cabinet edges.
The Deltana solid brass cabinet hinge in brushed chrome with ball tip finials offers a 2-1/2 inch by 2 inch full mortise footprint, which fits well where a compact, semi-concealed hinge is needed on cabinet doors. The 0.093 inch leaf thickness and square corners define the mortise depth and shape, helping cabinetmakers cut consistent pockets across multiple doors. With six fastener holes sized for #7 by 3/4 inch wood screws, the hinge spreads load into the frame and door edge to support regular cabinet use. For projects calling for solid brass construction and a brushed chrome finish within the semi-concealed face-frame hinge class, this model provides a defined size and mounting style that align with precise cabinet work.