Amerock Aloft Series 8-9/16 in (217 mm) Center to Center Polished Chrome Tab Pull, -BP3674626

Amerock Aloft Tab Pull For Contemporary Cabinets

Amerock Aloft tab pull turns the practical handle into a sleek detail by using a graceful curvature that creates a visually seamless design along the cabinet edge. This Amerock Corporation pull is part of the Aloft collection, so it keeps a consistent modern look across matching hardware. The tab-style form works as a decorative handle and pull in one piece, which keeps fronts clean while still giving a defined gripping point. Its subtle profile adds sophistication to contemporary spaces where low visual clutter matters. The polished chrome finish reflects light, which helps doors and drawers read crisp and sharp in finished installations. An overall length of 11-11/16 in (297 mm) spans a wide portion of the front, so the pull reads as a linear design detail instead of a small point grip.

Key Amerock Aloft Edge Pull Jobsite Advantages

• The aluminum material keeps the Aloft edge pull light, which helps when using multiple pulls on large cabinet runs and supports easier handling during layout and fastening.
• The polished chrome finish on the tab pull delivers a bright, reflective surface that visually pairs with other polished chrome hardware in the same project.
• The 8-9/16 in (217 mm) center-to-center dimension gives a generous gripping span, which suits wider cabinet doors or drawers where users expect a full-hand pull point.
• The 1-9/16 in (40 mm) projection provides finger clearance from the cabinet face, which supports a comfortable pull without crowding the hand against the door or drawer surface.
• The 11/16 in (17 mm) width keeps the pull profile slim across the edge, which helps maintain tight visual lines on frameless or modern face-frame cabinetry.
• The matching base length of 11-11/16 in (297 mm) and base width of 11/16 in (17 mm) create a uniform footprint, which simplifies layout when repeating this pull across multiple fronts.

Edge Pull Dimensions That Support Clean Installation

The Aloft edge pull uses an 8-9/16 in (217 mm) center-to-center dimension, which sets a fixed hole spread for drilling or boring operations on doors and drawers. With an overall and base length of 11-11/16 in (297 mm), the pull overhangs the mounting points at both ends, so the line of the pull visually frames the hole pattern and hides minor edge variance on the front. A projection of 1-9/16 in (40 mm) stands the grip off the face enough to clear fingers while still keeping the silhouette tight to the cabinet for a modern look. The 11/16 in (17 mm) width and base width keep the pull narrow, which fits well on slim rails or door edges without crowding adjacent details.

Using The Aloft Edge Pull On Cabinet Runs

Where This Amerock Aloft Tab Pull Fits Best

This Amerock Aloft Series pull is designed as a decorative handle and pull within the Handles and Pulls category, so it fits cabinet and furniture fronts that call for a linear grip along the edge. The Aloft collection styling supports use in contemporary spaces, where a subtle profile is preferred over bulky handles. With an 11-11/16 in (297 mm) overall length, the pull suits wider drawers or tall doors that benefit from a longer gripping bar rather than multiple small handles. The polished chrome finish lines up with other polished chrome elements in a room, so the pull can tie in with hinges or other decorative hardware from Amerock on the same job.

Dimensions And Build That Promote Repeatable Results

The 217 mm center-to-center layout gives a precise drilling pattern that can be repeated across banks of doors and drawers, which helps maintain alignment when working with jigs or CNC programs. Because the base length and overall length both measure 11-11/16 in (297 mm), installers can register the pull to door edges knowing the visible and bearing surfaces match, reducing visual shifts from part to part. The aluminum material keeps each pull light while still forming a continuous tab, which can ease handling during large quantity installs. A projection of 1-9/16 in (40 mm) gives users a predictable hand feel from cabinet to cabinet, supporting consistent operation across an entire kitchen or casework run. The 11/16 in (17 mm) width remains constant along the base, so spacing between pulls on multi-drawer stacks can follow tight reveals without the hardware looking oversized.

Common Questions About Amerock Aloft Edge Pull BP3674626

Select This Aloft Pull For Precise Modern Runs

The Amerock Aloft Series 8-9/16 in center-to-center polished chrome tab pull BP3674626 pairs a defined 217 mm drilling pattern with an 11-11/16 in (297 mm) overall length, which suits aligned cabinet runs. The aluminum construction and 1-9/16 in (40 mm) projection support a consistent hand feel across doors and drawers while keeping the look streamlined. For projects calling for a contemporary Amerock decorative handle that reads as a continuous edge detail, this Aloft edge pull delivers the dimensions and finish needed to keep fronts clean and coordinated.