Nexis Cam Adjustable Wing Mounting Plate, 2-Point Fixing, Screw-On, 0mm

Nexis Cam Adjustable Wing Mounting Plate Details

Nexis cam adjustable wing mounting plate provides a hinge mounting solution built around a 0mm plate height, which sets the hinge arm close to the cabinet side and supports standard layout where no extra height offset is desired. This component belongs to the hinge mounting plates product class from Grass America, so it functions as the interface between the cabinet side and a compatible Nexis hinge. The plate uses a wing mounting design, which spreads the bearing surface on the cabinet side and helps distribute hinge loads across a wider area during everyday door operation. Its two-point fixing configuration uses two fasteners on the cabinet side, giving a defined, repeatable position when installing multiple doors in a run. As part of the Nexis system, the cam design in this plate supports later hinge alignment changes without disturbing the basic screw-on installation on the case side.

Key Nexis Mounting Plate Features In Use

• Nexis two cam adjustment base plates offer plus or minus 2 mm of cam height adjustment, so an installer can raise or lower the door position slightly after initial mounting to correct margins along the cabinet.
• The same Nexis two cam adjustment base plates provide plus 3 mm and minus 1 mm of cam depth adjustment, allowing fine tuning of the door-to-cabinet gap to help doors sit flush and operate smoothly.
• The hinge affixes to the plate via a clip-on design, so hinges can be attached or removed from the mounted plate without releasing the cabinet side screws, which speeds door hanging and later service work.
• The cabinet side affixing method uses open holes sized for #6 wood screws, providing a straightforward screw-on process with a familiar fastener size for typical cabinet case materials.
• This version is described as a two point fixing plate, using two mounting points on the cabinet side to establish consistent hinge positioning when repeating the layout across multiple doors.
• Nexis two cam adjustment base plates are available in 0 mm through 8 mm heights, so the 0mm plate can be selected when a flush starting height is needed within a broader system of offset options.

Installation And Mounting Workflow Details

The cabinet side affixing method for this Nexis cam adjustable wing mounting plate is an open hole pattern sized for #6 wood screws, which lets installers drive standard flat head screws directly into the cabinet side without special inserts. Because this model uses a two point fixing configuration, the plate aligns off two screw locations, giving a predictable hinge reference line that suits repetitive drilling patterns on casework. The hinge connection uses a clip-on interface, so once the plates are secured with #6 x 5/8 inch flat head screws, doors can be hung by snapping the Nexis hinges onto the plates instead of handling loose screws at the hinge arm. With cam adjustments providing plus or minus 2 mm in height and plus 3 mm and minus 1 mm in depth, fine-tuning can be done at the plate, reducing the need to reposition screws after initial installation.

Using This Nexis Plate In Cabinet Projects

Where This Nexis 0mm Wing Plate Fits

This Nexis 0mm 3D cam wing plate functions as a hinge mounting base on the cabinet side for Nexis hinges, so it is positioned on case interiors where doors need adjustable alignment. The 0mm plate height places the hinge arm at the reference level of the cabinet panel, which supports layouts designed around a neutral base height without additional offset. Its wing-style footprint spreads onto the cabinet surface, so it supports usage on standard cabinet sides where load distribution across the substrate is beneficial. The two-point fixing pattern using #6 x 5/8 inch flat head screws suits typical cabinet side materials found in woodworking projects, as it relies on a simple screw-on method into the case wall without separate brackets. Within the Nexis range, this 0mm height option fits projects that prioritize minimal stack height between the hinge and the cabinet side.

Why Nexis Cam Adjustment Supports Precise Results

The Nexis two cam adjustment design on this mounting plate offers plus or minus 2 mm of cam height movement, which allows the door to be shifted up or down relative to the cabinet opening to achieve even reveals after all doors are hung. The same cam system provides plus 3 mm and minus 1 mm of depth adjustment, so the door can be brought closer to or slightly away from the cabinet front to align door faces in a bank. With the hinge attaching to the plate via a clip-on design, installers can separate the door from the case while leaving the plate and screws untouched, which simplifies hinge adjustments on installed cabinets. The screw-on method using open holes sized for #6 wood screws supports rapid installation because the mounting plate is located, fastened, and then adjusted by cam rather than by re-drilling. Across multiple cabinets using Nexis two cam adjustment base plates from 0 mm through 8 mm heights, the same adjustment logic applies, supporting consistent alignment practices when mixing different plate heights to solve layout conditions.

Common Questions About This Nexis Mounting Plate

Selecting This Nexis Plate For Your Project

This Nexis cam adjustable wing mounting plate from Grass America combines a 0mm height, clip-on hinge interface, and two cam adjustment for height and depth, so it suits cabinet work that needs precise door alignment from a neutral base height. Its open holes for #6 x 5/8 inch flat head screws match standard cabinet fastening habits, helping installers integrate it smoothly into existing drilling patterns. For cabinet runs designed around Nexis hinge hardware and requiring fine margin control, this hinge mounting plate provides the cam-based adjustability needed to dial in reveals efficiently.