EXTENT EDGE PULL 167MM CC STN NKL describes an Amerock Extent Series tab pull designed as a slim, modern grab point for cabinet fronts. The 6-9/16 in (167 mm) center-to-center dimension sets a consistent drilling layout, which supports uniform alignment across runs of doors and drawers. The overall 9-3/4 in length gives a generous hand space along the edge, which helps when operating wider fronts. The 1-5/8 in projection stands the pull off the surface just enough for fingers to wrap behind, which aids comfortable operation without crowding adjacent fronts. The 13/16 in width keeps the profile lean, which works well where a low visual line is preferred. The satin nickel finish provides a muted metallic look, which fits projects calling for a contemporary but not overly shiny appearance. Aluminum construction keeps weight down, which is useful on lighter cabinet faces.
The 6-9/16 in (167 mm) center-to-center drilling dimension on this Amerock satin nickel tab pull provides a defined mounting pattern, which supports accurate placement on door and drawer fronts. The pull uses M4 threaded screw interfaces, which aligns with common cabinet pull fastening methods for straightforward attachment. The 1-5/8 in projection works within typical cabinet clearances, which helps the pull operate without interference where fronts meet. The 13/16 in width concentrates contact along a slim strip, which allows placement near panel edges without overwhelming narrow rails. The 9-3/4 in overall length extends past the drilled points, which creates additional leverage along the edge for opening motions. The aluminum body keeps installation handling manageable, which is useful when working multiple pulls during a cabinet run.
The Amerock Extent Series tab pull, at 9-3/4 in overall length, works as a linear handle along cabinet edges, which suits contemporary layouts favoring long, low-profile hardware. The 6-9/16 in (167 mm) center-to-center spacing defines the structural mounting zone, which helps keep drilling consistent across banks of drawers or doors that share a design line. Its 1-5/8 in projection gives a defined grab point away from the face, which supports easy pull action on heavier fronts without needing deep finger recesses. With a 13/16 in width, the pull presents a modest face band, which integrates into modern cabinet styles where hardware should support the design rather than dominate it. The satin nickel finish supplies a soft metallic tone, which coordinates with satin nickel decorative hardware specified elsewhere in the project for a unified appearance.
The 167 mm center-to-center metric on this BP36752G10 Amerock pull provides a precise reference, which aids in using drilling jigs or templates for repeatable installation across multiple fronts. The M4 threaded connection matches a common fastener standard, which allows installers to rely on familiar tooling and fastening practices when setting the pulls. The 1-5/8 in projection and 13/16 in width define the envelope off the face, which helps plan door spacing so fronts can open without hardware-to-hardware contact. The aluminum construction keeps each pull lighter than many solid metal options, which reduces added load on standard cabinet hinges and slides. The Extent Series identity ties this pull to a named collection, which supports coordinated selection of other Amerock decorative hardware pieces in the same project where visual continuity matters.
The Amerock BP36752G10 pull has 6-9/16 in (167 mm) center-to-center spacing, which sets the distance between mounting holes for drilling and layout.
The Amerock Extent Series BP36752G10 measures 9-3/4 in in overall length, which provides a long gripping edge along the cabinet front.
The BP36752G10 satin nickel tab pull is made from aluminum, which keeps the hardware lightweight on cabinet doors and drawers.
This Amerock Extent pull projects 1-5/8 in from the cabinet surface, which creates room for fingers to grab behind the pull.
The Amerock BP36752G10 pull has a 13/16 in width, which presents a slim visible band on the cabinet front.
This 167 mm center-to-center pull uses a satin nickel finish, which offers a subdued metallic look on cabinet installations.
The Amerock Extent Series BP36752G10 satin nickel tab pull combines a 6-9/16 in (167 mm) center-to-center pattern with a 9-3/4 in overall length, which supports aligned runs of modern cabinet hardware. The 1-5/8 in projection and 13/16 in width define a slim, functional profile, which fits designs calling for a contemporary linear pull. Aluminum construction and the satin nickel finish deliver a light, metal-fronted handle, which coordinates with other satin nickel decorative hardware. For projects needing a defined 167 mm center-to-center edge pull, this Amerock option provides those dimensions in a tab pull format.
Sold In: 1 Each
