4' Aluminum Extruded By-passing Double Track 7002

4' Aluminum Double Track For Sliding Doors

4' aluminum extruded by-passing double track 7002 delivers a matched pair of tracks that guide sliding doors so they move in front of and behind each other, which supports compact access openings in built-ins and similar projects. The double aluminum carrier tracks layout keeps two door panels on separate runs, so each door has a defined path that reduces interference as panels pass. The 4 foot length suits many standard-width openings, giving installers a ready-to-use section that often minimizes field cutting. Aluminum construction creates a rigid track body that supports smooth carrier travel under typical sliding door loads. The extruded profile shapes the running surfaces consistently along the full length, which helps maintain even movement from end to end and supports clean door alignment.

Key Sliding Track Details For Daily Use

• Double aluminum carrier tracks provide two parallel runs for door carriers, so paired sliding doors can pass each other cleanly in by-passing layouts and maintain predictable motion during everyday operation.
• Holes at every 11 inches along the track establish regular fastening points, helping create uniform support on the mounting surface and promoting consistent alignment over the full span once secured.
• The 4 foot overall length gives a defined coverage width for sliding door openings, which helps installers plan door panel sizing and track placement with fewer splices in common cabinet or closet spans.
• Aluminum material keeps the track lightweight while staying structurally stable, which aids handling during overhead or wall-level mounting and supports long runs without excessive sag.

Sliding Track Mounting And Fastener Details

Double aluminum carrier tracks with holes at every 11 inches give installers preset locations for mechanical fastening, so the track can be anchored in a consistent pattern along its length. This regular spacing supports even load transfer into the substrate when door carriers move along the track. The recommended fasteners are #8 x 1-1/4 inch panhead screws, which pair the track with a commonly used screw size so installers can align their fastening choice to the manufacturer guidance. Panhead screw geometry bears against the track surface broadly, helping clamp the aluminum profile securely to the mounting surface. The 4 foot track length means layout and drilling steps align to a finite run, simplifying measurement when marking fastening positions and related hardware locations.

Using This Sliding Door Hardware In Projects

Where This Double Track Works In Sliding Layouts

The 4 foot aluminum extruded by-passing double track 7002 fits projects that call for two sliding doors sharing an opening, because the paired carrier runs support front and rear door movement. In cabinet or closet-style applications, the 4 foot span matches many typical opening widths, so the track can extend nearly the full clear width and support smooth travel across the face of the unit. Double aluminum carrier tracks define separate paths for each door panel, which helps doors overlap properly without binding where panels cross. Holes at every 11 inches give a repeatable fastening rhythm along that span, so the track can be tied into face frames, headers, or similar framing at predictable intervals across the opening. With Hettich America Corporation providing this sliding door hardware, the track aligns with a recognized builders hardware and sliding door hardware product class used in woodworking shops.

Why These Track Details Support Consistent Results

The extruded aluminum construction keeps the running surfaces of the double aluminum carrier tracks uniform, which helps carriers roll smoothly and maintain consistent door reveal from one end of the track to the other. The by-passing double track format separates the two sliding paths, so each door panel uses its designated run and continues to clear the other door through the full travel distance. Fastener holes at every 11 inches translate into predictable connection points, allowing the track to share sliding loads across multiple supports rather than concentrating stress at just a few locations. The 4 foot track length limits joint lines in many openings, which reduces the chance of misalignment where two shorter tracks would meet. Recommended #8 x 1-1/4 inch panhead screws engage the track at those hole positions, helping clamp the aluminum extrusion firmly and maintain straightness over time while doors cycle.

Common Questions About This Hettich Door Track

Selecting This Track For Sliding Door Runs

The 4 foot aluminum extruded by-passing double track 7002 from Hettich America Corporation offers a defined-length solution for two-door sliding openings, with double aluminum carrier tracks that separate door paths and a hole pattern at every 11 inches that supports regular fastening. Using the recommended #8 x 1-1/4 inch panhead screws with this builders hardware sliding track gives installers a clear hardware pairing for mounting into cabinet or framing members. For woodworking projects that need a compact, by-passing sliding door hardware layout across an opening near 4 feet wide, this Hettich 50526 double track aligns sliding movement, fastening pattern, and material choice into one track run.