Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
CompX National Removacore cam lock gives installers a master keyed cam lock solution for drawers and doors requiring controlled access across multiple lock points. The 90 and 180 degree cam turn design uses stop washers to set rotation, so the same cylinder adapts to different door and drawer layouts. The 1-3/4 inch cylinder length provides reach for thicker panel constructions common in casework. A bright nickel finish presents a clean, uniform appearance where the lock face remains visible. The Removacore system is factory master keyed, so once assembled the master key operates any compatible pre-assembled disc tumbler from CompX National that is factory master keyed (KAMKD or KDMKD), which supports keyed-alike and master key plans in one system. Separate core plug and cylinder assembly keeps the housing in the casework while cores follow your key control needs.
This Removacore cam lock cylinder assembly requires a 3/4 inch diameter hole for installation, so standard boring tools used for many cam locks apply directly. The housing is supplied with a trim washer and spur washer for wood, supporting a flush, stable fit against wood doors or drawer fronts. Mounting nuts secure the cylinder from the rear, which keeps the visible side clean while locking the body to the panel. Two cams are provided, a straight cam with 1-1/2 inch extension and a formed cam with 1-1/8 inch extension and 11/32 inch offset, allowing the lock to reach different strikes or frame details without reworking the case geometry.
This Removacore cam lock is specified for drawers and for right-hand or left-hand doors, whether lipped, flush, or overlay, so one lock family covers a wide range of cabinet conditions. The right-hand and left-hand door suitability allows the installer to apply the same cylinder assembly on either swing, which simplifies layout on mirrored runs. Lipped, flush, and overlay compatibility means the cams and washers are configured so the locking bar can engage catches on different door edge styles without changing the basic housing. The straight cam with 1-1/2 inch extension helps reach strikes on flat or inset frames, while the formed cam with 1-1/8 inch extension and 11/32 inch offset steps around obstructions or engages hardware on offset faces. This flexibility supports mixed cabinet construction within the same project.
The Removacore system uses a separate core plug and cylinder assembly, so the lock housing stays fixed in the cabinet while cores can be installed, removed, or rekeyed using a control key. This approach keeps drilling and casework fitting as a one-time task, with keying handled through the removable core. Once assembled, the masterkey for the Removacore will open any pre-assembled disc tumbler from CompX National that is factory master keyed (KAMKD or KDMKD), which ties this cam lock into broader master key plans using those tumbler series. The key is removable in the locked position only, which supports a closed-and-locked routine before the key can be withdrawn. A control key is required to install core plugs into the cylinder assembly, defining who can change cores in the field. Plugs are supplied with 2 keys, giving two operating keys per plug for daily users while maintaining separate control key access.
The CompX National Removacore cam lock requires a 3/4 inch diameter hole, so boring to this size sets the cylinder correctly in doors or drawer fronts.
The Removacore cam lock is specified for drawers and for right-hand or left-hand lipped, flush, or overlay doors, covering typical cabinet and casework layouts.
The 90 and 180 degree cam turn arrangement uses two stop washers so the installer sets 90 or 180 degree rotation, matching the cam travel to the latch orientation.
The Removacore system is factory master keyed, and once assembled the masterkey opens compatible CompX National factory master keyed disc tumbler locks KAMKD or KDMKD.
The M5-7054N-14A Removacore cam lock uses a 1-3/4 inch cylinder, which helps span thicker drawer fronts or doors in many woodworking applications.
The Removacore cam lock allows key removal only in the locked position, supporting lock-and-remove-key routines on cabinets and casework.
The CompX National Removacore cam lock with 1-3/4 inch cylinder, bright nickel finish, and selectable 90 or 180 degree cam turn provides a practical option for drawers and doors needing coordinated master key control. The 3/4 inch mounting hole requirement, trim and spur washers for wood, rear mounting nuts, and supplied straight and formed cams together support straightforward casework installation on lipped, flush, or overlay doors and drawers. For projects using CompX National factory master keyed disc tumbler series KAMKD or KDMKD, this cylinder assembly ties those locations into a single Removacore master key plan.
Sold In: 1 Each
