John Boos Butcherblock Backsplash 4"H x 60"L x 3/4"T Hard Maple, RS60-O

John Boos Butcher Block Backsplash For Wood Tops

John Boos butcher block backsplash gives a hard maple upstand that finishes off a butcher block run and protects the rear edge of the work surface. The backsplash is constructed of high quality Northern Hard Maple hardwood, so it matches typical John Boos butcher block countertops in both species and visual character. The 4 inch height and 60 inch length create a substantial barrier along the wall interface, which helps keep splashes off the wall surface in normal countertop use. The 3/4 inch thickness provides a solid wood profile that works well where a sturdy, furniture-like detail is needed. The mineral oil finish seals the wood fibers, which supports resistance to incidental moisture and brings out the warm rich colors of the grain, so the installed piece reads as a continuous extension of the top.

Key Maple Backsplash Details For Job Planning

• The backsplash measures 4 inches high by 60 inches long, which gives a consistent height reference along the rear of a standard-length butcher block counter and simplifies layout against straight walls.
• The 3/4 inch thickness offers a traditional butcher block edge profile, so installers and fabricators can plan straightforward transitions at corners and end points without dealing with unusual dimensions.
• The high quality Northern Hard Maple hardwood construction matches John Boos butcher block surfaces, which helps create a uniform appearance where countertop and backsplash meet in the finished installation.
• The kiln dried hardwood is produced with low moisture content, which supports dimensional stability during normal shop handling and typical interior kitchen or workroom conditions.
• The moisture resistant urea resin adhesive used in electrostatic gluing supports bond strength between maple strips, which is important when cutting or drilling during fabrication or fitting on site.
• The mineral oil finish seals the wood fibers and enriches the grain color, which allows the backsplash to coordinate visually with oiled butcher block tops right after installation.

Installation Considerations For Maple Backsplash Fit

This 4 inch by 60 inch hard maple backsplash is sized for straight runs where a continuous rear edge is required behind a butcher block or similar wood countertop. The 3/4 inch thickness aligns with common butcher block edge thickness, which helps create a clean joint line where the vertical backsplash meets the horizontal surface. Because the backsplash is kiln dried for low moisture content, it behaves predictably when trimmed to fit, which supports accurate scribing against walls. The mineral oil finish on the maple surface is already in place, so field cuts can focus on fit and alignment around corners or wall irregularities without needing to address raw factory faces over the majority of the part.

Using The RS60-O Backsplash In Real Projects

Where This 4 x 60 Maple Backsplash Works

The John Boos and Company RS60-O backsplash is part of the John Boos butcher block product class, so it fits naturally into projects using wood countertops in kitchens, workrooms, or shop surfaces that call for butcher block styling. The 4 inch height provides a generous visual band of Northern Hard Maple behind the work surface, which suits applications where the wall transition needs a strong, furniture-like detail rather than a narrow trim strip. With its 60 inch length, the backsplash spans a typical five-foot section of counter without seams, which is useful when laying out straight runs along a single wall segment. Because the wood is kiln dried for low moisture content, it supports interior environments where humidity varies in normal ranges, helping keep the rear edge of the counter visually aligned with the backsplash line over time.

Details That Support Consistent Backsplash Results

The hard maple construction of this backsplash provides a dense, uniform material, which helps routed or trimmed edges stay crisp when fabricators adjust length or miter corners during installation. Electrostatic gluing with a moisture resistant urea resin adhesive bonds the maple components into a single solid piece, which supports clean cuts without joint separation when customizing the part. The mineral oil finish that seals the wood fibers also enhances the warm rich colors of the grain, which matters when aligning the backsplash with a butcher block top so the two read as a coordinated surface. Because the backsplash can be retreated with mineral oil as needed, installers and owners can maintain a consistent appearance between top and backsplash over the life of the installation, supporting a uniform look even as the wood is exposed to routine use.

Common Questions About This Maple Backsplash

Select This RS60-O Backsplash For Maple Tops

The John Boos butcher block backsplash RS60-O offers a 4 inch high, 60 inch long, 3/4 inch thick Northern Hard Maple solution that visually and materially complements wood countertops. With kiln dried construction, moisture resistant adhesive, and a mineral oil finish that can be retreated as needed, it supports projects where a solid maple rear edge and coordinated butcher block appearance are important. For woodworkers and installers planning butcher block runs that call for a continuous maple upstand, this RS60-O backsplash provides a defined size and finish that fits straightforward project layout and long-term visual alignment needs.