Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
This Salice Series 200 concealed hinge opens to 120 degrees for generous door access, hangs full overlay doors on face-frame and frameless cabinets, and uses dowel mounting for production-friendly installation in pre-bored doors.
A 120 degree opening is the right call on cabinets where the extra swing matters: tall pantry doors, deep base cabinets, corner pulls, and any run where adjacent walls or appliances sit close but not quite close enough to demand a restricted-angle hinge. The additional swing over the standard 110 degree hinge is modest, but it can make the difference between a door that clears a refrigerator handle and one that does not.
The 35mm cup bores into the back of the door in the standard position, and the dowels press into the door's pre-bored holes without cup screws. A separate Salice base plate mounts to the cabinet side or face-frame stile, sold separately. The hinge arm clips to that plate during installation. Use Salice plates with this hinge — plates are brand-specific and not interchangeable with other manufacturers.
The hinge body is plated steel in a nickel finish. Nickel reads as a cool, light metallic tone that pairs naturally with chrome, brushed aluminum, and satin silver pulls and knobs. On a kitchen or bath run where the visible hardware carries a brushed or satin finish, this hinge keeps the cabinet interior visually consistent when doors stand open. The self-close spring means the door does not stay open to show the hinge unless you hold it, so the finish is more about the install moment and the detail-oriented buyer than daily visibility.
The dowel mount is the differentiator here for volume shops. Where a screw-on cup requires positioning and driving two screws per hinge at the door, a dowel mount presses straight into the CNC-bored holes, which is faster on a line. Cabinet shops running pre-bored door blanks, remodelers fitting doors to a prepared carcass, and production contractors who want cup attachment to follow the boring pattern rather than hand-fitting screws will find this hinge suits their process. It works on both frameless and face-frame cabinets, so it carries through a mixed job without a switch.
This is a self-close hinge. The spring pulls the door shut once released within a few degrees of closed, which is the reliable, low-maintenance option for most residential and light commercial work. If the project calls for a damped, cushioned close, the Silentia+ soft-close version of the Series 200 is the correct choice.
No. The hinge mounts to a Salice base plate that is sold separately. Match the plate to your cabinet construction — frameless wing or face-frame style — and order it alongside the hinges.
This hinge is self-close: a spring draws the door shut over the last few degrees. Soft-close uses a damper to slow the door so it settles quietly. If you need a cushioned, slam-free close, choose the Silentia+ soft-close version of the Series 200.
The hinge cup carries pre-attached dowels that press into bored holes in the door rather than using cup screws. This suits CNC-bored door blanks and speeds installation on a production line. The cup position is set by the boring, so accurate CNC work is important.
No. Salice plates are brand-specific. A plate from Blum, Grass, or another manufacturer will not connect to this hinge. Use Salice Series 200 plates matched to your cabinet type.
Hinge count depends on door height, width, and weight. As a general guide, doors up to about 40 inches tall use two hinges and taller doors use three or more. Refer to the Salice load table for the exact figure for your door.
Choose this hinge when a 120 degree swing improves access, dowel mounting fits your boring workflow, and a nickel finish matches the hardware palette — all in a dependable Series 200 self-close that keeps installations moving.
Sold In: 1 Each
Quantity | Unit Price | Catalog | ||||
|---|---|---|---|---|---|---|
Sold in: 1 Each |  UBS2A637XF Mfr# S2A637XF | Salice 94° Hinge Stop Device for Series 200 Hinges S2A637XF |
